欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ISP1123
廠商: NXP Semiconductors N.V.
英文描述: Universal Serial Bus compound hub
中文描述: 通用串行總線復合樞紐
文件頁數: 8/49頁
文件大小: 1155K
代理商: ISP1123
Philips Semiconductors
ISP1123
USB compound hub
Preliminary specification
Rev. 01 — 5 October 1999
8 of 49
9397 750 06325
Philips Electronics N.V. 1999. All rights reserved.
[1]
[2]
Symbol names with an overscore (e.g. NAME) indicate active LOW signals.
The voltage at pin V
reg(3.3)
is gated by the RESET pin. This allows fully self-powered operation by
connecting RESET to V
BUS
(+5 V USB supply). If V
BUS
is lost upstream port D+ will not be driven.
See
Table 4 “Mode selection”
.
To disable a downstream port connect both D
+
and D
to V
CC
via a 1 M
resistor; unused ports must
be disabled in reverse order starting from port 5.
Analog detection circuit can be switched off using an external EEPROM, see
Table 23
; in this case,
the pin functions as a logic input (TTL level).
Downstream ports 1 and 2 cannot be disabled.
[3]
[4]
[5]
[6]
7.
Functional description
The ISP1123 is a compound USB hub with up to 5 downstream ports. The number of
ports can be configured between 2 and 5. The downstream ports can be used to
connect low-speed or full-speed USB peripherals. Downstream port 1 is dedicated to
an embedded or non-removable function, the other ports are removable.
All standard USB requests from the host are handled by the hardware without the
need for firmware intervention. The block diagram is shown in
Figure 1
and the basic
architecture of a compound hub in
Figure 2
.
The ISP1123 requires only a single supply voltage. An internal 3.3 V regulator
provides the supply voltage for the analog USB data transceivers.
The ISP1123 supports both bus-powered and self-powered hub operation. When
using bus-powered operation a downstream port cannot supply more than 100 mA to
a peripheral. In case of self-powered operation an external supply is used to power
the downstream ports, allowing a current consumption of max. 500 mA per port.
A basic I
2
C-bus interface is provided for reading vendor ID, product ID and
configuration bits from an external EEPROM upon a reset.
7.1 Analog transceivers
The integrated transceiver interfaces directly to the USB cables through external
termination resistors. They are capable of transmitting and receiving serial data at
both ‘full-speed’ (12 Mbit/s) and ‘low-speed’ (1.5 Mbit/s) data rates. The slew rates
are adjusted according to the speed of the device connected and lie within the range
mentioned in the USB Specification Rev. 1.1
DM2
DP2
PSW1/GL1
[3]
26
27
28
AI/O
AI/O
O
downstream port 2 D
connection (analog)
[6]
downstream port 2 D
+
connection (analog)
[6]
modes 4 to 6
: power switch control output for downstream
port 1 (open-drain, 6 mA)
modes 0 to 3, 7
: GoodLink LED indicator output for
downstream port 1 (open-drain, 6 mA); to connect an LED
use a 330
series resistor
Table 3:
Symbol
[1]
Pin description for LQFP32
…continued
Pin
Type
Description
相關PDF資料
PDF描述
ISP1123D Universal Serial Bus compound hub
ISP1123NB Universal Serial Bus compound hub
ISP1130 Universal Serial Bus compound hub with integrated keyboard controller
ISP1130DL Universal Serial Bus compound hub with integrated keyboard controller
ISP1130N Universal Serial Bus compound hub with integrated keyboard controller
相關代理商/技術參數
參數描述
ISP1123BD 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub
ISP1123D 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub
ISP1123NB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub
ISP1130 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller
ISP1130DL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller
主站蜘蛛池模板: 蓬溪县| 东至县| 南漳县| 扬中市| 绥德县| 瑞丽市| 长寿区| 桓台县| 宁海县| 民权县| 平乡县| 南京市| 乐都县| 江陵县| 秦皇岛市| 常德市| 紫阳县| 东丽区| 赞皇县| 肇庆市| 平原县| 红原县| 达孜县| 广州市| 内乡县| 景德镇市| 威海市| 公主岭市| 桐庐县| 南木林县| 綦江县| 漳州市| 和政县| 永顺县| 永清县| 鄄城县| 施甸县| 广西| 台山市| 田阳县| 五台县|