欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ISP1123D
廠商: NXP SEMICONDUCTORS
元件分類: 總線控制器
英文描述: Universal Serial Bus compound hub
中文描述: UNIVERSAL SERIAL BUS CONTROLLER, PDSO32
封裝: 7.50 MM, PLASTIC, SO-32
文件頁數: 43/49頁
文件大小: 1155K
代理商: ISP1123D
Philips Semiconductors
ISP1123
USB compound hub
Preliminary specification
Rev. 01 — 5 October 1999
43 of 49
9397 750 06325
Philips Electronics N.V. 1999. All rights reserved.
19. Soldering
19.1 Introduction
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all IC packages. Wave soldering is often
preferred when through-hole and surface mount components are mixed on one
printed-circuit board. However, wave soldering is not always suitable for surface
mount ICs, or for printed-circuit boards with high population densities. In these
situations reflow soldering is often used.
19.2 Surface mount packages
19.2.1
Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, infrared/convection heating in a
conveyor type oven. Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°
C. The top-surface
temperature of the packages should preferable be kept below 230
°
C.
19.2.2
Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
相關PDF資料
PDF描述
ISP1123NB Universal Serial Bus compound hub
ISP1130 Universal Serial Bus compound hub with integrated keyboard controller
ISP1130DL Universal Serial Bus compound hub with integrated keyboard controller
ISP1130N Universal Serial Bus compound hub with integrated keyboard controller
ISP1160 Embedded Universal Serial Bus Host Controller
相關代理商/技術參數
參數描述
ISP1123NB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub
ISP1130 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller
ISP1130DL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller
ISP1130N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller
ISP1160 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller
主站蜘蛛池模板: 会理县| 永善县| 崇信县| 黔西县| 华阴市| 和政县| 洞口县| 丰县| 诏安县| 炎陵县| 平泉县| 甘孜县| 西畴县| 孝义市| 凭祥市| 和硕县| 南皮县| 云霄县| 丹棱县| 手游| 营口市| 寻乌县| 平邑县| 湾仔区| 兴安盟| 福鼎市| 大邑县| 文山县| 丹江口市| 石首市| 开封县| 浦城县| 任丘市| 习水县| 高陵县| 上饶市| 喀喇| 九龙坡区| 肥西县| 河池市| 额济纳旗|