- 您現在的位置：買賣IC網 > PDF目錄376103 > JT6N38S TRANSPONDER|CMOS|DIE PDF資料下載
參數資料
| 型號： | JT6N38S |
| 英文描述： | TRANSPONDER|CMOS|DIE |
| 中文描述： | 轉發器|的CMOS |模具 |
| 文件頁數： | 1/7頁 |
| 文件大小： | 111K |
| 代理商： | JT6N38S |
JT6N38S
2000-07-21 1/7
TOSHIBA CMOS Integrated Circuit Silicon Monolithic
J T 6 N 3 8 S
Single-Chip System LSI for RFID Card
The JT6N38S is a system LSI for radio frequency identification (RFID) wireless cards. The JT6N38S
incorporates an analog circuit, a data processing circuit and data memory in a single chip.
Features
High-noise-resistant PSK modulation:
binary phase-shift keying (BPSK) for both reader-to-RFID and RFID-to-reader transmission.
Start-stop synchronization and half-duplex transmission: with parity, 1 stop bit
High-efficiency power generation circuit using electromagnetic induction:
battery less operation, full-wave rectifier circuit, shunt regulator
Data processing logic circuit: digital PLL, security circuit
High-reliablity E
2
PROM: 4 Kbits
Maximum write time: 7 ms (16-byte batch write)
Overwrite: 100,000 times
Data retention: 10 years
Selectable receive carrier frequency: 120 kHz to 500 kHz (when external antenna circuit is used)
Serial transmitter circuit (for active PSK): long-distance communication supported
Programmable security circuit: security level can be set
High-speed transfer rate of 25 kbps: 1/16 of receive carrier frequency
=
400 kHz
High-speed multi-read of 32 IDs per second: when receive carrier frequency
=
400 kHz (ID only read)
Supplied as chips or on wafer
Chip thickness: 175
μ
m (typ.)
TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general
can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the
buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and
to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or
damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the
most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling
Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc..
The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal
equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are
neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or
failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy
control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control
instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document
shall be made at the customer’s own risk.
The products described in this document are subject to the foreign exchange and foreign trade laws.
The products described in this document contain components made in the United States and subject to export control of the U.S.
authorities. Diversion contrary to the U.S. law is prohibited.
The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its
use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or
others.
The information contained herein is subject to change without notice.
000707EDA1
相關PDF資料 |
PDF描述 |
|---|---|
| JT6N46S | Transponder |
| JT6N78S | TRANSPONDER|CMOS|DIE |
| JT6P21-AS | Watch Circuit |
| JT6P24-AS | Display Counter |
| JT7579A-AS | Watch Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| JT7-1104NL | 功能描述:1 Port RJ45 Magjack Connector Through Hole 10G Base-T, AutoMDIX 制造商:pulse electronics corporation 系列:PULSEJACK? JT7 包裝:托盤 零件狀態:有效 連接器類型:RJ45 端口數:1 排數:1 應用:10G Base-T，AutoMDIX 安裝類型:通孔 朝向:90°角（直角） 端接:焊接 板上高度:0.525"（13.33mm） LED 顏色:綠，黃 - 綠 每插孔芯數:8 屏蔽:屏蔽式，EMI指 特性:板導軌 凸片方向:上 觸頭材料:磷青銅 觸頭鍍層:金 觸頭鍍層厚度:50μin（1.27μm） 屏蔽材料:銅合金 外殼材料:熱塑塑膠 工作溫度:0°C ~ 70°C 標準包裝:50 |
| JT7-1115NL | 功能描述:1 Port RJ45 Magjack Connector Through Hole 10G Base-T, AutoMDIX 制造商:pulse electronics corporation 系列:PULSEJACK? JT7 包裝:托盤 零件狀態:有效 連接器類型:RJ45 端口數:1 排數:1 應用:10G Base-T，AutoMDIX 安裝類型:通孔 朝向:90°角（直角） 端接:焊接 板上高度:0.525"（13.33mm） LED 顏色:綠，黃 - 綠 每插孔芯數:10 屏蔽:屏蔽式，EMI指 特性:板導軌 凸片方向:上 觸頭材料:磷青銅 觸頭鍍層:金 觸頭鍍層厚度:50μin（1.27μm） 屏蔽材料:銅合金 外殼材料:熱塑塑膠 工作溫度:0°C ~ 70°C 標準包裝:50 |
| JT7-1119NL | 功能描述:1 Port RJ45 Magjack Connector Through Hole 10G Base-T, AutoMDIX 制造商:pulse electronics corporation 系列:PULSEJACK? JT7 包裝:- 零件狀態:新產品 連接器類型:RJ45 端口數:1 排數:1 應用:10G Base-T，AutoMDIX 安裝類型:通孔 朝向:90°角（直角） 端接:焊接 板上高度:0.525"（13.33mm） LED 顏色:綠，黃 - 綠 每插孔芯數:8 屏蔽:屏蔽式，EMI指 特性:板導軌 凸片方向:上 觸頭材料:磷青銅 觸頭鍍層:金 觸頭鍍層厚度:50μin（1.27μm） 屏蔽材料:銅合金 外殼材料:熱塑塑膠 工作溫度:0°C ~ 70°C 標準包裝:200 |
| JT75 | 制造商:JAUCH 制造商全稱:Jauch Quartz Gmbh 功能描述:Oscillator |
| JT7579A-AS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Watch Circuit |
發布緊急采購，3分鐘左右您將得到回復。