- 您現在的位置：買賣IC網 > PDF目錄374310 > KAC-749S (Electronic Theatre Controls, Inc.) 4-Channel power amplifier PDF資料下載
參數資料
| 型號： | KAC-749S |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 4-Channel power amplifier |
| 中文描述： | 4通道功率放大器 |
| 文件頁數： | 1/2頁 |
| 文件大小： | 373K |
| 代理商： | KAC-749S |
Installation procedure
1.Remove the ignition key and disconnect the
negative
-
terminal of the battery to prevent
short circuits.
2.Set the unit according to the intended usage.
3.Connect the input and output cables of the
units.
4.Connect the speaker wires.
5.Connect the power wire, power control wire
and grounding wire following this order.
6.Install the unit in the car.
7.Connect the negative
-
terminal of the battery.
To prevent fire caused by a short in the wiring,
connect a fusible link or breaker nearby the
battery’s positive terminal.
Be sure to turn the power off before changing the
setting of any switch.
If the fuse blows, check wires for shorts, then
replace the fuse with one of the same rating.
Check that no unconnected cables or connectors
are touching the car body. Do not remove caps from
unconnected cables or connectors to prevent short
circuits.
Connect the speaker wires to appropriate speaker
connectors separately. Sharing the negative wire of
the speaker or grounding speaker wires to the metal
body of the car can cause this unit to fail.
After installation, check that the brake lamps,
winkers, and wipers work properly.
I
Speaker level input terminals (
!
)
The genuine-accessory car stereo shall have a
maximum power output of no more than 40 W.
Do not connect the speaker output leads from
a power amplifier (Optional) to the speaker
level input terminals of this unit, for this may
cause malfunction or damage.
Do not connect cables and leads to both RCA
cable input jacks and the speaker level input
terminals simultaneously, for this may cause
malfunction or damage.
Connect the power control lead to a power
supply which can be turned ON/OFF by the
ignition key switch (ACC line). With this
connection, shock noise may be generated
when the power of the genuine-accessory car
stereo is switched ON/OFF.
I
Power terminal (
234
)
Connect to their respective terminals the power
supply wire, and ground wire, all of which pass
through the associated terminal cover. Once the
connections are complete, place the cover on
the terminal section.
2
CAUTION
2
WARNING
PRINTED IN USA B64-1969-00 (KM/EM)
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help
you obtain the best performance from your new power amplifier.
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below.
Refer to the model and serial numbers whenever you call upon your
KENWOOD dealer for information or service on the product.
Model KAC-849/749S Serial number
4
3 Channel Mode...............................................100 W
′
2 + 300 W
′
1
2 Channel Mode ...................................................................300 W
′
2
Rated Power Output (4
)
4 Channel Mode (20 Hz ~ 20 kHz, less than 0.08 % THD).....50 W
′
4
4 Channel Mode
(DIN45324, +B=14.4V)................................50 W
′
4
3 Channel Mode (20 Hz ~ 20 kHz, 0.08 % THD) + (1 kHz, 0.8 % THD)
...........................................................................50 W
′
2 + 150 W
′
1
2 Channel Mode (1 kHz, 0.8 % THD)....................................150 W
′
2
Rated Power Output (2
)
4 Channel Mode (1 kHz, 0.8 % THD)......................................75 W
′
4
Frequency Response (+0, –3 dB)......................................5 Hz ~ 50 kHz
Signal to Noise Ratio ....................................................................100 dB
Sensitivity (MAX) (rated output).......................................................0.2 V
Sensitivity
(MIN) (rated output)........................................................5.0 V
Input Impedance ............................................................................10 k
Low Pass Filter Frequency (12 dB/oct.) (Variable)................50 ~ 200 Hz
High Pass Filter Frequency (12 dB/oct.) (Variable)................50 ~ 200 Hz
Bass Boost Circuit (90 Hz)................................................................6 dB
80 W
′
2 + 250 W
′
1
250 W
′
2
40 W
′
4
40 W
′
4
40 W
′
2 + 120 W
′
1
120 W
′
2
60 W
′
4
5 Hz ~ 50 kHz
100 dB
0.2 V
5.0 V
10 k
50 ~ 200 Hz
50 ~ 200 Hz
6 dB
General
..................................................................................
KAC-849
Operating Voltage (11 ~ 16 V allowable) .......................................14.4 V
Current Consumption (1 kHz, 10 % THD) ........................................31 A
Dimensions (W
′
H
′
D)...........................................261
′
57
′
256 mm
......................................................................
(10-1/4
′
2-1/4
′
10-1/16 in.)
Weight................................................................................3.5 kg (7.7 lb)
KAC-749S
14.4 V
26 A
261
′
57
′
256 mm
(10-1/4
′
2-1/4
′
10-1/16 in.)
3.5 kg (7.7 lb)
Safety precautions
To prevent injury or fire, take the following
precautions:
When extending the ignition, battery, or ground
wires, make sure to use automotive-grade wires or
other wires with a 5mm
2
(AWG10) or more to
prevent wire deterioration and damage to the wire
coating.
To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
If the unit starts to emit smoke or strange smells,
turn off the power immediately and consult your
Kenwood dealer.
Do not touch the unit during use because the surface
of the unit becomes hot and may cause burns if
touched.
To prevent damage to the machine, take the
following precautions:
Be sure the unit is connected to a 12V DC power
supply with a negative ground connection.
Do not open the top or bottom covers of the unit.
Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
When replacing a fuse, only use a new one with the
prescribed rating. Using a fuse with the wrong rating
may cause your unit to malfunction.
To prevent a short circuit when replacing a fuse, first
disconnect the wiring harness.
If you experience problems during installation,
consult your Kenwood dealer.
If the unit does not seem to be working right, consult
your Kenwood dealer.
FCC WARNING
This equipment may generate or use radio frequency
energy. Changes or modifications to this equipment
may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate
this equipment if an unauthorized change or
modification is made.
I
Cleaning the unit
If the front panel gets dirty, turn off the power and
wipe the panel with a dry silicon cloth or soft cloth.
Do not wipe the panel with a hard cloth or a cloth
dampened by volatile solvents such as paint thinner
and alcohol. They can scratch the surface of the panel
and/or cause the indicator letters to peel off.
I
Wiring
If a buzzing noise is heard from the speakers
when the engine is running, connect a line noise
filter (optional) to each of the battery wire.
Do not allow the wire to directly contact the edge
of the iron plate by using Grommets.
Connect the ground wire to a metal part of the
car chassis that acts as an electrical ground
passing electricity to the battery‘s negative
-
terminal. Do not turn the power on if the ground
wire is not connected.
Be sure to attach a protective fuse into the
battery wire close to the battery. Use a
protective fuse having a capacity that is about 10
A higher than the maximum current drawn by the
amplifier.
Use vehicle-type (fire-resistant) power supply
wiring wire for the battery wire and the ground
wire. The current capacity of the power supply
wiring wire should be about 10 A higher than that
of the protective fuse capacity (which means
about 20 A higher than the maximum current
drawn by the amplifier).
When more than one power amplifier are going
to be used, use a power supply wiring wire and
protective fuse of greater current-handling
capacity than the total maximum current drawn
by each amplifier.
Example: One Power Amplifier Is Used
I
Speaker Selection
The rated input power of the speakers that are
going to be connected should be greater than
the maximum output power (in Watts) of the
amplifier. Use of speakers having input power
ratings that are less than the output power of
the amplifier will cause smoke to be emitted as
well as damage.
The impedance of the speakers that are going to
be connected should be 2
or greater (for
stereo connections), or 4
or greater (for
bridged connections). When more than one set
of speakers are going to be used, calculate the
combined impedance of the speakers and then
connect suitable speakers to the amplifier.
2
CAUTION
NOTE
2
CAUTION
2
WARNING
Maximum Current Drawn
Protective Fuse
Cross-sectional Area of
Wiring Wire (AWG)
31 A / 26 A
50 A
′
1 [25 A
′
2]
5 mm
2
(AWG 10) or
greater
′
1
8
2
4
4
4
4
25 A
25 A
25 A
25 A
相關PDF資料 |
PDF描述 |
|---|---|
| KAD0228BD | 8-BIT 30 MSPS CMOS A/D CONVERTER |
| KAQV210 | MOS RELAYS |
| KAQV212S | HIGH VOLTAGE, SOLID STATE RELAY - MOSFET OUTPUT |
| KAQV214A | HIGH VOLTAGE, PHOTO EDMOS RELAY |
| KAQV214S | HIGH VOLTAGE PHOTO MOS RELAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KAC-8 | 功能描述:保險絲 600V 8A Semiconductor RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| KAC-80 | 功能描述:保險絲 600V 80A Semiconductor RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| KAC-800 | 功能描述:保險絲 600V 800A Semiconductor RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| KAC8NP47 | 功能描述:機架和機柜配件 REPLACEMENT FILTER RoHS:否 制造商:Bivar 產品:Rack Accessories 面板空間: 顏色:Black |
| KAC-9 | 制造商:COOPER 制造商全稱:Cooper Bussmann, Inc. 功能描述:High Speed Fuses |
發布緊急采購，3分鐘左右您將得到回復。