- 您現在的位置：買賣IC網 > PDF目錄367493 > L8560 Low-Power SLIC with Ringing PDF資料下載
參數資料
| 型號： | L8560 |
| 英文描述： | Low-Power SLIC with Ringing |
| 中文描述： | 低功耗振鈴用戶接口 |
| 文件頁數： | 23/46頁 |
| 文件大小： | 842K |
| 代理商： | L8560 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Lucent Technologies Inc.
23
Data Sheet
April 2000
L8560 Low-Power SLIC with Ringing
Applications
(continued)
dc Applications
(continued)
12-2563.c (F)
Figure 23. SLIC 2-Wire Output Stage
In addition to the required peak signal level, the SLIC
needs about 2 V from each power supply to bias the
amplifier circuitry. It can be thought of as an internal
saturation voltage. Combining the saturation voltage
and the peak signal level, the required overhead can
be expressed as:
x 10
dBm/20
where V
SAT
is the combined internal saturation voltage
between the tip/ring amplifiers and V
BAT
(4.0 V typ.). R
P
(
) is the protection resistor value. Z
T/R
(
) is the ac
loop impedance.
Example 1, On-Hook Transmission of a Meter
Pulse:
Signal level: 2.2 Vrms into 200
35
protection resistors
I
LOOP
= 0 (on-hook transmission of the metering signal)
V
OH
= 4.0 +
(2.2)
= 8.2 V
Accounting for V
SAT
tolerance of 0.5 V, a nominal over-
head of 8.7 V would ensure transmission of an undis-
torted 2.2 V metering signal.
Adjusting Overhead Voltage
To adjust the open loop 2-wire voltage, pin DCR
(44-pin PLCC only) is programmed at the midpoint of a
resistive divider from ground to either –5 V or V
BAT
. In
the case of –5 V, the overhead voltage will be indepen-
dent of the battery voltage. Figure 24 shows the equiv-
alent input circuit to adjust the overhead.
12-2562.b (F)
Figure 24. Equivalent Circuit for Adjusting the
Overhead Voltage
The overhead voltage is programmed by using the fol-
lowing equation:
V
OH
= 7.1 – 18.18 V
DCR
= 7.1 – 18.18
Adjusting dc Feed Resistance
The dc feed resistance may be adjusted with the help
of Figure 25.
12-2560.c (F)
Figure 25. Equivalent Circuit for Adjusting the dc
Feed Resistance
R
dc
= 55
+ 705
= 55
+ 705
–
V
T/R
[Z
T/R
]
V
AMP
–
+
R
P
R
P
+
V
OH
V
SAT
1
Z
T/R
-----------
+
V
T/R
+
=
Λ
V
SAT
1
Z
T/R
-----------
+
1000
--------------
+
=
1
----------------
200
+
2
DCR
R
1
R
2
–5 V
5
–
+
R
2
R
1
---------------------
×
DCR
R
1
R
3
DCOUT
44-PIN PLCC
DCR
V
DCOUT
--------V
+
R
3
R
1
---------------------
相關PDF資料 |
PDF描述 |
|---|---|
| L8567 | SLIC for Peoples Republic of China Applications |
| L8567-32PLCC | Telecommunication IC |
| L8567-44PLCC | Telecommunication IC |
| L8574D | CAP 15PF 50V 5% C0G SMD-0402 TR-7-PA SN100 |
| L8575 | Dual-Resistive,Low-Cost Subscriber Line Interface Circuit(SLIC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L8560AAU | 制造商:Alcatel-Lucent 功能描述: 制造商:LUCENT 功能描述: |
| L8561 | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:The UTC L8561 is a Power Factor Corrector, which can work in wide input voltage range applications (from 85V ~ 265V) with an excellent THD. |
| L8561_11 | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:POWER FACTOR CORRECTOR |
| L8561G-D08-T | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:POWER FACTOR CORRECTOR |
| L8561G-S08-R | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:POWER FACTOR CORRECTOR |
發布緊急采購，3分鐘左右您將得到回復。