- 您現在的位置：買賣IC網 > PDF目錄367494 > L9215A CAP CER 2200PF 3.15KVDC R3 RAD PDF資料下載
參數資料
| 型號： | L9215A |
| 英文描述： | CAP CER 2200PF 3.15KVDC R3 RAD |
| 中文描述： | 短回路正弦波振鈴用戶接口 |
| 文件頁數： | 28/50頁 |
| 文件大小： | 1115K |
| 代理商： | L9215A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Data Sheet
September 2001
Short-Loop Sine Wave Ringing SLIC
L9215A/G
28
Agere Systems Inc.
Supervision
(continued)
Power Ring
(continued)
Sine Wave Input Signal and Sine Wave Power Ring
Signal Output
The low-voltage sine wave input is applied to the L9215
at pin RING
IN
. This signal should be ac-coupled
through 0.47
μ
F. During the ring mode, the signal at
RING
IN
is amplified and presented to the subscriber
loop. The differential gain from RING
IN
to tip and ring is
a nominal 55.
When the device enters the ring mode, the tip/ring
overhead set at OVH and the scan clamp circuit is dis-
abled, allowing the voltage magnitude of the power ring
signal to be maximized. Additionally, in the ring mode,
the loop current limit is increased 2.5X the value set by
the V
PROG
voltage.
The magnitude of the power ring voltage will be a func-
tion of the gain of the ring amplifier, the high-voltage
battery, and the input signal at RING
IN
. The input range
of the signal at RING
IN
is 0 V to Vcc. As the input volt-
age at RING
IN
is increased, the magnitude of the power
ring voltage at tip and ring will increase linearly, per the
differential gain of 55, until the tip and ring drive amplifi-
ers begin to saturate. Once the tip and ring amplifiers
reach saturation, further increases of the input signal
will cause clipping distortion of the power ring signal at
tip and ring. The ring signal will appear balanced on tip
and ring. That is, the power ring signal is applied to
both tip and ring, with the signal on tip 180
°
out of
phase from the signal on ring.
Figure 11 shows typical operation of the ring mode,
prior to saturation of the tip and ring drive amplifiers. A
–70 V battery is used with a 100
loop and a 1 REN
load. The input signal is 1 V through a 0.47
μ
F capaci-
tor at RING
IN
, (the input circuit is shown in Figure 12).
This produces a voltage swing from –34 V to –60 V on
ring and from –8 V to –34 V on tip, as shown in Figure
11. Thus, the total voltage swing is 52 V (60 V to 8 V)
for a 1 V input, which is approximately the differential
gain of the device. Note that the tip and ring power ring
signals will swing around V
BATTERY
divided by two. In
this case, there is a –70 V battery so tip and ring swing
around –34 V.
12-3573F
12-3574F
Figure 11. Ring Mode Typical Operation
0
–60
0.60
0.62
0.64
0.66
0.68
0.70
0.72
0.74
0.76
0.78
TIME
0.80
–20
–40
VRING
VTIP
1.0
–1.0
0.60
0.62
0.64
0.66
0.68
0.70
0.72
0.74
0.76
0.78
TIME
0.80
0.5
0.0
–0.5
VRINGIN
相關PDF資料 |
PDF描述 |
|---|---|
| L9216A | CAP CER 270PF 3.15KVDC R3 RAD |
| L9217A | CAP CER 2700PF 3.15KVDC R3 RAD |
| L9218A | CAP CER 330PF 3.15KVDC R3 RAD |
| L9219A | CAP CER 390PF 3.15KVDC R3 RAD |
| L9310 | Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9216A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start |
| L9217A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| L9218A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
| L9219A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
| L9222 | 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。