- 您現在的位置：買賣IC網 > PDF目錄367494 > L9216A CAP CER 270PF 3.15KVDC R3 RAD PDF資料下載
參數資料
| 型號： | L9216A |
| 英文描述： | CAP CER 270PF 3.15KVDC R3 RAD |
| 中文描述： | 短環振鈴用戶接口與地面開始 |
| 文件頁數： | 30/48頁 |
| 文件大小： | 1062K |
| 代理商： | L9216A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Preliminary Data Sheet
September 2001
Short-Loop Ringing SLIC with Ground Start
L9216A/G
30
Agere Systems Inc.
Supervision
(continued)
Power Ring
(continued)
3.3 V V
CC
Operation
A PWM signal was generated with an HP8116 Func-
tion Generator modulated with a 20 Hz signal. The opti-
mal frequency used was 10 kHz. The PWM signal
amplitude was 3.10 V (0 V to 3.10 V). This input signal
is shown in Figure 17.
12-3571F
Figure 17. 3.3 V PWM Signal Amplitude
This produced 44.96 Vrms ringing signal on tip/ring
under open-loop conditions and 42.0 Vrms was deliv-
ered to 5 REN load. The ringing output on ring with V
CC
= 3.1 V is shown in Figure 18.
1660
Notes:
The modulating 20 Hz signal THD was measured at 1.3%.
The tip/ring 20 Hz signal THD was measured at 1%.
V
BAT1
= –70.6 V, V
BAT2
= –26.5 V, V
CC
= 3.10 V.
PWM input 10 kHz, 3.1 Vp-p.
R
1
= 10 k
, C
1
= 0.22
μ
F, C
2
= 0.47
μ
F.
Figure 18. Ringing Output on RING, with V
CC
= 3.1 V
During nonring modes, the PWM waveform may be left
on at RING
IN
. Via the state table, the ring signal will be
removed from tip and ring even if the low-voltage input
is still present at RING
IN
. There are certain timing con-
siderations that should be made with respect to state
changes which are detailed in the Switching Behavior
of L9215/6 Ringing SLICApplication Note.
Square Wave Input Signal and Trapezoidal Power
Ring Signal Output
A low-voltage square wave signal may be used to pro-
vide the ringing input to RING
IN
. The signal is applied
through a low-pass filter and ac-coupled into RING
IN
as
shown in Figure 13 and Table 23. This approach gives
a trapezoidal wave output at tip and ring.
Using this approach, a trapezoidal waveform can be
achieved at tip and ring. This has the advantage of
increasing the power transfer to the load for a given
battery voltage, thus increasing the effective ringing
loop length as compared to a sine wave. The actual
crest factor achieved is a function of the magnitude of
the battery, the magnitude of the input voltage, fre-
quency, and R
1
.
12-3572F
Notes:
CH1—CMOS Input (5 V) at RING
IN
.
CH2—Filtered input at RING
IN
.
CH3—Tip.
CH4—Ring.
R
1
= 14 k
, C
1
= 1.0
μ
F, C
2
= 0.47
μ
F.
V
BAT1
= –70 V, Vrms
= 51 V, V
p-p
= 67 V, frequency = 20 Hz, Crest
Factor = 1.3.
Figure 19. Square Wave Input Signal and Trapezoi-
dal Power Ring Signal Output
CH1
CH2
CH3
CH4
相關PDF資料 |
PDF描述 |
|---|---|
| L9217A | CAP CER 2700PF 3.15KVDC R3 RAD |
| L9218A | CAP CER 330PF 3.15KVDC R3 RAD |
| L9219A | CAP CER 390PF 3.15KVDC R3 RAD |
| L9310 | Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device |
| L9311 | Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9217A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| L9218A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
| L9219A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
| L9222 | 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L9222_04 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD INVERTING TRANSISTOR SWITCH |
發布緊急采購，3分鐘左右您將得到回復。