欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: L9217A
英文描述: CAP CER 2700PF 3.15KVDC R3 RAD
中文描述: 低成本線接口,具有反向電池和PPM
文件頁數: 19/30頁
文件大小: 414K
代理商: L9217A
Agere Systems Inc.
19
Data Sheet
November 2001
with Reverse Battery and PPM
L9217A/G Low-Cost Line Interface
Applications
(continued)
dc Applications
Battery Feed
The dc feed characteristic can be described by:
where:
I
L
= dc loop current.
V
T/R
= dc loop voltage.
|
V
BAT
|
= battery voltage magnitude.
V
OH
= overhead voltage. This is the difference between
the battery voltage and the open loop tip/ring
voltage.
R
L
= loop resistance, not including protection resistors.
R
P
= protection resistor value.
R
dc
= SLIC internal dc feed resistance.
Note: V
BAT
= –48 V; I
LIM
= 22 mA; R
dc1
= 115
.
Figure 13. Loop Current vs. Loop Voltage
Starting from the on-hook condition and going through
to a short circuit, the curve passes through the follow-
ing two regions:
Region 1: On-hook and low-loop currents. The slope
corresponds to the dc resistance of the SLIC, R
dc1
(default is 72
typical). The open circuit voltage is
the battery voltage minus the overhead voltage of the
device, V
OH
(default is 6.5 V typical). These values are
suitable for most applications but can be adjusted if
needed.
Region 2: Current limit. The dc current is limited to a
starting value determined by external resistor R
PROG
,
an internal current source, and the gain from tip/ring to
pin VITR. Current limit with a 100
load is set by the
following equation:
0.637 R
PROG
(k
) + 2 mA = I
LIM
x (mA)
Overhead Voltage
In order to drive an on-hook ac signal, the SLIC must
set up the tip and ring voltage to a value less than the
battery voltage. The amount that the open loop voltage
is decreased relative to the battery is referred to as the
overhead voltage. This is expressed as the following
equation:
V
OH
= |V
BAT
| – (V
PT
– V
PR
)
Without this buffer voltage, amplifier saturation will
occur and the signal will be clipped. In modes without
PPM, the L9217 is set to allow undistorted on-hook
transmission of a 3.17 dBm signal into a 900
loop
impedance. A minimum 11.1 V overhead is needed to
pass 3.5 Vrms meter pulse.
In high overhead and PPM modes, overhead is auto-
matically increased to accommodate on-hook trans-
mission of meter pulse signals. The increase in
overhead is set by a resistor from pin OVH to ground.
This is expressed as the following equation:
V
OVH
(V) = 6.37 + 0.09535 x R
OVH
(k
)
I
L
R
L
+
R
dc
+
2R
P
---------------------------------
=
V
T/R
R
L
2R
P
---------------------------------------------
R
dc
L
+
+
=
0
10
20
50
0
20
30
40
50
LOOP VOLTAGE (V)
30
40
10
L
1
12.5 k
–1
R
dc1
I
LIM
TESTED
I
LIM
ONSET
12-3050 (F).i
相關PDF資料
PDF描述
L9218A CAP CER 330PF 3.15KVDC R3 RAD
L9219A CAP CER 390PF 3.15KVDC R3 RAD
L9310 Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
L9311 Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access
L9312 Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications
相關代理商/技術參數
參數描述
L9218A 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface
L9219A 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit
L9222 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L9222_04 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD INVERTING TRANSISTOR SWITCH
L9222D 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
主站蜘蛛池模板: 车险| 绥棱县| 前郭尔| 邯郸县| 鹿泉市| 密山市| 定州市| 金塔县| 化州市| 东宁县| 玉溪市| 哈尔滨市| 舟曲县| 平潭县| 蓬安县| 平阳县| 玉溪市| 吴忠市| 黑山县| 临颍县| 达州市| 澄江县| 宝山区| 南昌县| 昌邑市| 嘉黎县| 佛教| 遵化市| 鄯善县| 昭苏县| 香格里拉县| 唐河县| 平度市| 驻马店市| 盱眙县| 黑河市| 祥云县| 庆阳市| 东兴市| 陆川县| 耿马|