- 您現在的位置：買賣IC網 > PDF目錄367494 > L9219A CAP CER 390PF 3.15KVDC R3 RAD PDF資料下載
參數資料
| 型號： | L9219A |
| 英文描述： | CAP CER 390PF 3.15KVDC R3 RAD |
| 中文描述： | 低成本線接口，具有反向電池和雙電流限制 |
| 文件頁數： | 27/30頁 |
| 文件大小： | 397K |
| 代理商： | L9219A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁
Agere Systems Inc.
27
Data Sheet
November 2001
with Reverse Battery and Dual Current Limit
L9219A/G Low-Cost Line Interface
Applications
(continued)
Power Derating
Operating temperature range, maximum current limit,
maximum battery voltage, minimum dc loop, and pro-
tection resistor values will influence the overall thermal
performance. This section shows the relevant design
equations and considerations in evaluating the SLIC
thermal performance.
Consider the L9219 SLIC in a 28-pin PLCC package.
The still-air thermal resistance on a 2 layer board is
43 °C/W.
The SLIC will enter the thermal shutdown state at mini-
mally 150
°C. The thermal shutdown design should
ensure that the SLIC temperature does not reach
150
°
C under normal operating conditions.
Assume a maximum ambient operating temperature of
85 °C, a maximum current limit of 25 mA (including tol-
erance), and a maximum battery of –52 V. Further-
more, assume a (worst case) minimum dc loop of
200
, and that 50
protection resistors are used at
both tip and ring.
1. T
TSD
– T
AMBIENT(max)
= allowed thermal rise.
150 °C – 85 °C = 65 °C
2. Allowed thermal rise = package thermal
impedance
SLIC power dissipation.
65 °C = 43 °C/W
SLIC power dissipation
SLIC power dissipation (P
DISS
) = 1.51 W
Thus, if the total power dissipated in the SLIC is less
than 1.51 W, it will not enter the thermal shutdown
state. Total SLIC power is calculated as:
Total P
DISS
= Maximum battery
Maximum
current limit (including effects of accuracy)
+ SLIC quiescent power.
For the L9219, SLIC quiescent power (P
Q
) is maximum
at 0.158 W. Thus,
Total P
DISS
= (–52 V
[25 mA
1.05])
+ 0.158 W
Total P
DISS
= 1.365 W + 0.158 W
Total P
DISS
= 1.523 W
The power dissipated in the SLIC is the total power dis-
sipation minus the power that is dissipated in the loop.
SLIC P
DISS
= Total power – Loop power
Loop power = (I
LIM
)
2
(R
dcLOOP
min + 2R
P
)
Loop power = (25 mA
1.05)
2
(200
+ 100
)
Loop power = 0.207 W
SLIC power = 1.523 W – 0.207 W = 1.28
SLIC power = 1.28 W < 1.51 W
Thus, in this example, the thermal design ensures that
the SLIC will not enter the thermal shutdown state.
Pin-for-Pin Compatibility with L9217/L9218
The L9219 is an exact pin-for-pin replacement for the
L9217/18. The one minor exception is L9219 has three
logic control inputs: B0, B1, and B2. The L9218 has
only two logic control inputs, B0 and B1. Pin 13 in
L9218 is NC, so a connection between the controller
and pin 13 will not affect L9218 operation. This allows
an exact footprint match with L9219.
PCB Layout Information
Make the leads to BGND and V
BAT
as wide as possible
for thermal and electrical reasons. Also, maximize the
amount of PCB copper in the area of (and specifically
on) the leads connected to this device for the lowest
operating temperature.
When powering the device, ensure that no external
potential creates a voltage on any pin of the device that
exceeds the device ratings. In this application, some of
the conditions that cause such potentials during pow-
erup are the following:
1. An inductor connected to PT and PR (this can force
an overvoltage on V
BAT
through the protection
devices if the V
BAT
connection chatters).
2. Inductance in the V
BAT
lead (this could resonate with
the V
BAT
filter capacitor to cause a destructive over-
voltage).
This device is normally used on a circuit card that is
subjected to hot plug-in, meaning the card is plugged
into a biased backplane connector. In order to prevent
damage to the IC, all ground connections must be
applied before, and removed after, all other connec-
tions.
相關PDF資料 |
PDF描述 |
|---|---|
| L9310 | Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device |
| L9311 | Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access |
| L9312 | Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| L9313 | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| L9350 | Single Peripheral Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9222 | 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L9222_04 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD INVERTING TRANSISTOR SWITCH |
| L9222D | 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L9222-D | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD INVERTING TRANSISTOR SWITCH |
| L9222D013TR | 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。