- 您現在的位置：買賣IC網 > PDF目錄30713 > L9950 (STMICROELECTRONICS) BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 PDF資料下載
參數資料
| 型號： | L9950 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| 封裝： | ROHS COMPLIANT, SSOP-36 |
| 文件頁數： | 20/39頁 |
| 文件大小： | 620K |
| 代理商： | L9950 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
L9950 - L9950XP
Functional description of the SPI
Doc ID 10311 Rev 10
Table 19.
SPI - input data and status registers 0
Bit
Input register 0 (write)
Status register 0 (read)
Name
Comment
Name
Comment
23
Enable bit
If Enable Bit is set the
device will be switched in
active mode. If Enable Bit
is cleared device go into
standby mode and all bits
are cleared. After power-
on reset device starts in
standby mode.
Always 1
A broken VCC or SPI
connection of the L9950 can
be detected by the
microcontroller, because all 24
bits low or high is not a valid
frame.
22
Reset bit
If Reset Bit is set both
status registers will be
cleared after rising edge
of CSN input.
VS overvoltage
In case of an overvoltage or
undervoltage event the
corresponding bit is set and
the outputs are deactivated. If
VS voltage recovers to normal
operating conditions outputs
are reactivated automatically
(if Bit 20 of status register 0 is
not set).
21
OC recovery
duty cycle
This bit defines in
combination with the over-
current recovery bit (Input
Register 1) the duty cycle
in over-current condition
of an activated driver.
VS undervoltage
0: 12%
1:
25%
20
Overvoltage/Un
dervoltage
recovery disable
If this bit is set the
microcontroller has to
clear the status register
after
undervoltage/overvoltage
event to enable the
outputs.
Thermal
shutdown
In case of an thermal
shutdown all outputs are
switched off.
The microcontroller has to
clear the TSD bit by setting the
Reset Bit to reactivate the
outputs.
19
Depending on
combination of bit 18 and
19 the current image
(1/10.000) of the selected
HS output will be multi-
plexed to the CM output:
Temperature
warning
This bit is for information
purpose only. It can be used
for a thermal management by
the microcontroller to avoid a
thermal shutdown.
18
Current monitor
select bits
Bit
19
Bit
18
Output
Not ready bit
After switching the device from
standby mode to active mode
an internal timer is started to
allow charge pump to settle
before the outputs can be
activated. This bit is cleared
automatically after start up
time has finished. Since this
bit is controlled by internal
clock it can be used for
synchronizing testing events
(e.g. measuring filter times).
00
OUT11
10
OUT1/OUT
6
01
OUT5
11
OUT4
HS driver of OUT1 is only
selected if HS driver
OUT1 is switched on and
HS driver OUT6 is not
activated.
相關PDF資料 |
PDF描述 |
|---|---|
| L9950TR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9953XPTR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9953TR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9953 | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| LA1060 | SPECIALTY CONSUMER CIRCUIT, PSIP9 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9950_09 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Door actuator driver |
| L9950TR | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9950XP | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9950XPTR | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9951 | 功能描述:馬達/運動/點火控制器和驅動器 REAR DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。