欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: L9950TR
廠商: STMICROELECTRONICS
元件分類: 運動控制電子
英文描述: BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
封裝: ROHS COMPLIANT, SOP-36
文件頁數: 20/39頁
文件大小: 620K
代理商: L9950TR
L9950 - L9950XP
Functional description of the SPI
Doc ID 10311 Rev 10
Table 19.
SPI - input data and status registers 0
Bit
Input register 0 (write)
Status register 0 (read)
Name
Comment
Name
Comment
23
Enable bit
If Enable Bit is set the
device will be switched in
active mode. If Enable Bit
is cleared device go into
standby mode and all bits
are cleared. After power-
on reset device starts in
standby mode.
Always 1
A broken VCC or SPI
connection of the L9950 can
be detected by the
microcontroller, because all 24
bits low or high is not a valid
frame.
22
Reset bit
If Reset Bit is set both
status registers will be
cleared after rising edge
of CSN input.
VS overvoltage
In case of an overvoltage or
undervoltage event the
corresponding bit is set and
the outputs are deactivated. If
VS voltage recovers to normal
operating conditions outputs
are reactivated automatically
(if Bit 20 of status register 0 is
not set).
21
OC recovery
duty cycle
This bit defines in
combination with the over-
current recovery bit (Input
Register 1) the duty cycle
in over-current condition
of an activated driver.
VS undervoltage
0: 12%
1:
25%
20
Overvoltage/Un
dervoltage
recovery disable
If this bit is set the
microcontroller has to
clear the status register
after
undervoltage/overvoltage
event to enable the
outputs.
Thermal
shutdown
In case of an thermal
shutdown all outputs are
switched off.
The microcontroller has to
clear the TSD bit by setting the
Reset Bit to reactivate the
outputs.
19
Depending on
combination of bit 18 and
19 the current image
(1/10.000) of the selected
HS output will be multi-
plexed to the CM output:
Temperature
warning
This bit is for information
purpose only. It can be used
for a thermal management by
the microcontroller to avoid a
thermal shutdown.
18
Current monitor
select bits
Bit
19
Bit
18
Output
Not ready bit
After switching the device from
standby mode to active mode
an internal timer is started to
allow charge pump to settle
before the outputs can be
activated. This bit is cleared
automatically after start up
time has finished. Since this
bit is controlled by internal
clock it can be used for
synchronizing testing events
(e.g. measuring filter times).
00
OUT11
10
OUT1/OUT
6
01
OUT5
11
OUT4
HS driver of OUT1 is only
selected if HS driver
OUT1 is switched on and
HS driver OUT6 is not
activated.
相關PDF資料
PDF描述
L9953XPTR BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
L9953TR BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
L9953 BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
LA1060 SPECIALTY CONSUMER CIRCUIT, PSIP9
LA1061M SPECIALTY CONSUMER CIRCUIT, PDSO14
相關代理商/技術參數
參數描述
L9950XP 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L9950XPTR 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L9951 功能描述:馬達/運動/點火控制器和驅動器 REAR DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L9951_10 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Rear door actuator driver
L-995-12 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:NylaKrimp? Funnel Entry Ring Tongue Terminal for 4/0 AWG Wire, Stud #12
主站蜘蛛池模板: 汝州市| 淮滨县| 连州市| 博乐市| 绥江县| 常州市| 布拖县| 阿拉善左旗| 台东市| 朝阳县| 长治县| 额尔古纳市| 建德市| 绥中县| 西安市| 剑川县| 洞口县| 福鼎市| 神池县| 公安县| 清水河县| 北票市| 沅江市| 尼勒克县| 榆中县| 拜泉县| 临泽县| 德清县| 苍梧县| 雷山县| 武川县| 南溪县| 扬中市| 镇雄县| 定安县| 嵩明县| 石门县| 山东省| 郑州市| 苍南县| 逊克县|