- 您現在的位置：買賣IC網 > PDF目錄30715 > LA1888NM (SANYO SEMICONDUCTOR CO LTD) AM/FM, AUDIO SINGLE CHIP RECEIVER, PQFP64 PDF資料下載
參數資料
| 型號： | LA1888NM |
| 廠商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分類： | 接收器 |
| 英文描述： | AM/FM, AUDIO SINGLE CHIP RECEIVER, PQFP64 |
| 封裝： | QFP-64 |
| 文件頁數： | 8/10頁 |
| 文件大小： | 2592K |
| 代理商： | LA1888NM |
LA72710V
No.A0237-7/10
I
2C BUS serial interface specification
(1) Data Transfer Manual
This IC adopts control method (I
2C-BUS) with serial data, and controlled by two terminals which called SCL (serial
clock) and SDA (serial data). At first, set up
*1 the condition of starting data transfer, and after that, input 8 bit data to
SDA terminal with synchronized SCL terminal clock. The order of transferring is first, MSB (the Most Scale of Bit),
and save the order. The 9th bit takes ACK (Acknowledge) period, during SCL terminal takes ‘H’ this IC pull down the
SDA terminal. After transferred the necessary data, two terminals lead to set up and of
*2 data transfer stop condition,
thus the transfer comes to close.
*1 Defined by SCL rise down SDA during ‘H’ period.
*2 Defined by SCL rise up SDA during ‘H’ period.
(2) Transfer Data Format
After transfer start condition, transfers slave address (1000 000*B) to SDA terminal, control data, then, stop condition
(See figure 1).
Slave address is made up of 7bits, 8th bit
*3 shows the direction of transferring data, if it is ‘L’ takes write mode (As this
IC side, this is input operation mode), and in case of ‘H’ reading mode (As this IC side, this is output operation mode).
Data works with all of bit, transfer the stop condition before stop 8bit transfer, and to stop transfer, it will be canceled
the transfer dates.
*3 It is called R/W bit.
Fig.1 DATA STRUCTURE “WRITE” mode
START Condition
Slave Address
R/WL
ACK
Control data
ACK
STOP condition
Fig.2 DATA STRUCTURE “READ” mode
START condition
Slave Address
R/WH
ACK
Internal Data *
ACK
STOP condition
Output 8bits data as follows;
bit8 is result of STERO DET
(H : STEREO)
bit7 is result of BILINGUAL DET
(H : BILINGUAL)
bit6 to bit1 are fixed to ‘L’
(3) Initialize
This IC is initialized for circuit protection. Initial condition is “0 (All bits).”
相關PDF資料 |
PDF描述 |
|---|---|
| LA1888NM | AM/FM, AUDIO SINGLE CHIP RECEIVER, PQFP64 |
| LA188NM | 2-BAND, AUDIO TUNER, PQFP64 |
| LA1895M | 2-BAND, AUDIO TUNER, PQFP80 |
| LA2110M | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| LA2110 | SPECIALTY CONSUMER CIRCUIT, PZIP16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA1895M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Tuner IC for Car Radios |
| LA189W-G-S1 | 制造商:LIGITEK 制造商全稱:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA18B-G-PF | 制造商:LIGITEK 制造商全稱:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA190B-9UG-1-PF | 制造商:LIGITEK 制造商全稱:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA190B-DBK-2-PF | 制造商:LIGITEK 制造商全稱:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
發布緊急采購，3分鐘左右您將得到回復。