- 您現在的位置：買賣IC網 > PDF目錄30716 > LA4182 2.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 PDF資料下載
參數資料
| 型號： | LA4182 |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 2.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| 封裝： | DIP-12 |
| 文件頁數： | 5/10頁 |
| 文件大小： | 409K |
| 代理商： | LA4182 |
Description of External Parts
C1(C2)
Feedback capacitor
The low cutoff frequency depends on this capacitor. If the capacity is increased,
the starting time is delayed.
C3(C4)
Bootstrap capacitor
If the capacity is decreased, the output at low frequencies goes lower.
C5(C6)
Oscillation preventing capacitor
Polyester film capacitor, being good in temperature characteristic, frequency
characteristic, is used. If an aluminum electrolytic capacitor or ceramic capacitor
is used, oscillation may occur at low temperatures.
C7(C8)
Output capacitor
The low cutoff frequency depends on this capacitor. In order for the low
frequency characteristic in the bridge amplifier to be equal to that in the stereo
amplifier application, the capacity must be doubled.
C9
Decoupling capacitor
Used for the ripple filter. Since the rejection effect is saturated at a certain
capacity, it is meaningless to increase the capacity more than needed. This
capacitor, being also used for the time constant of the muting circuit, affects the
starting time.
C10
Power source capacitor
Application Circuit
1.
Voltage gain adjustment
k Stereo
The voltage gain depends on built-in resistors R1 (R2),
R3 (R4) as follows :
VG = 20log
R3 (R4)
R1 (R2)
[dB]
If the IC is used at a voltage gain less than this, the
following equation with Rf added applies.
VG = 20log
R3 (R4)
R1 (R2) + Rf
[dB]
where R1 (R2) = 50
,R3(R4)=10k
k Bridge
The above shows the bridge amplifier configuration, where ch.1 operates as a noninverting amplifier and ch.2 as an inverting
amplifier. The output of ch.1 is divided with R5, R6 and led to pin 1 and then input to ch.2.
Since the attenuation degree (R5/R6) of ch. 1 output and the amplification degree (R4/R2 + R6) of ch. 2 are fixed at an equal
value, the ch.2 output is in opposite phase with the ch. 1 output. Therefore, the total voltage gain gets apparently 6 dB higher
than the voltage gain of ch.1 alone and is determined by the following equation.
VG = 20log
R3
R1
+ 6 [dB]
If the IC is used at a voltage gain less than this, the following equation with Rf added applies.
VG = 20log
R3
R1+Rf
+ 6 [dB]
LA4182
No.742-4/10
相關PDF資料 |
PDF描述 |
|---|---|
| LA4183 | 2.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| LA4192 | 2.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| LA42032 | 5 W, 2 CHANNEL, AUDIO AMPLIFIER, SFM13 |
| LA42032 | 5 W, 2 CHANNEL, AUDIO AMPLIFIER, SFM13 |
| LA42051 | 5 W, 1 CHANNEL, AUDIO AMPLIFIER, SFM13 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA4183 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:2.3 W 2-Channel AF Power Amplifier for Radio Cassette Players |
| LA4185 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LA4185T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LA4190 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LA4192 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:2-CHANNEL AF POWER AMP FOR TAPE RECORDER RADIO |
發布緊急采購，3分鐘左右您將得到回復。