- 您現在的位置：買賣IC網 > PDF目錄30719 > LA4809M 0.16 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO12 PDF資料下載
參數資料
| 型號： | LA4809M |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 0.16 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO12 |
| 封裝： | 0.225 INCH, MFP-12 |
| 文件頁數： | 14/15頁 |
| 文件大小： | 252K |
| 代理商： | LA4809M |
LA4809M
Continued from preceding page.
When the standby function is not to be used, Pin 3 may be interlocked with power supply as shown in Fig.7. However,
due care must be taken in this case because such interlock makes the effectiveness of the pop noise reduction circuit
null, resulting in extremely large pop noise at a time of rising and falling. There are also methods to reduce the pop
noise by using two capacitors as shown in Fig.8. If pop noise is to be suppressed sufficiently, CPU control of the
standby pin is recommended.
Note that the approximate inrush current; I3 into the standby pin is calculated as follows :
Pin 3 inrush current (unit : A) : I3 = (5
× VCC - 4) × 10-5 /Rst
No.A1569-8/15
VCC
Rst
Fig.7
Fig.8
10. Operating power supply voltage range
The applicable power supply voltage range varies depending on the setting conditions of the maximum output power
value. Use this range while taking into account the Pin 2 voltage. As a guideline, the supply voltage at the lowest point
to be used must be two times the Pin 2 voltage.
Note that the minimum operating supply voltage must be 3.6V.
mode-B
VCC op = 6.2V to 17V
mode-A
VCC op = 4.2V to 17V
At change of the output power value due to external resistance
VCC op = 2 × V2 to 17V (V2 Pin 2
voltage)
11. Handling of NC pins (Pins 5, 8, and 11)
NC pins are not connected to anything internally and may be left in the OPEN state. To enhance the heat sink effect as
much as possible, connection of NC pins to the GND line is recommended.
In particular, Pin 5 should be connected to the GND line so as to protect Pin 4 (the first output).
If the pins 4 and 5 section and the pins 5 and 6 section are bridged with solder simultaneously, the output pin enters the
powering (short to power) state, allowing the large current to flow into the output pin, resulting in deterioration or
damage of internal elements. Risk of deterioration or damage may be reduced when Pin 5 is connected to GND. When
the output pin voltage is about 0.7V or less, drive and power stages of the power amplifier circuit used becomes
inoperable. In this context, the protection in case of ground fault is provided.
12. Heat protective circuit
The heat protective circuit is incorporated in IC and can reduce the risk of damage/deterioration in case of abnormal
heat generation due to certain reasons. This protective circuit is activated when the junction temperature : Ti of the chip
in IC increases to about 160
°C, shutting OFF current supply to the power amplifier. The signal is not output anymore.
When the chip temperature lowers (to about 130
°C), the circuit is automatically reset.
Note that this circuit is not always capable of preventing damage/deterioration and should be handled with utmost care.
In case of abnormal heating, turn OFF power supply immediately and identify the probable causes.
13. Short-circuit between pins
Power ON while leaving the pins in the short-circuit state may cause deterioration or damage. When installing IC to the
substrate, check if pins are short-circuited with solder before turning power supply ON.
14. Load short-circuit
Leaving the loads in the short-circuit state over a long period of time may cause deterioration or damage. Never
short-circuit loads.
15. Maximum rating
When the product is used near the maximum rating, even the smallest change in the conditions may cause exceeding of
the maximum rating, possibly leading to the fracture accident. Take the sufficient fluctuation margin for the supply
voltage and always use the product within a range never exceeding the maximum rating. The package used for this IC
has the low heat sink effect as a single unit. When the working supply voltage is high, solder the backside heat sink pad
to ensure sufficient heat sink performance with copper foil of printed circuit board.
VCC
Rst
6
STBY
3
VCC
6
STBY
+
Cst2
3
+
Cst1
相關PDF資料 |
PDF描述 |
|---|---|
| LA4809M | 0.16 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO12 |
| LA4810M | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO16 |
| LA4814V | 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LA4814V | 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LA4815M | 0.62 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA4809M-TLM-E | 功能描述:音頻放大器 STEREO HP AMPLIFIER RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LA4810M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Linear IC Stereo/Monaural BTL Power |
| LA4814JA | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Linear IC 2-Channel Power Amplifier |
| LA4814JA-AE | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LA4814JA-ZE | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。