- 您現在的位置：買賣IC網 > PDF目錄30719 > LA4815M 0.62 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | LA4815M |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 0.62 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封裝： | 0.225 INCH, MFP-8 |
| 文件頁數： | 11/14頁 |
| 文件大小： | 233K |
| 代理商： | LA4815M |
LA4815M
Notes on Using the IC
1. Voltage gain settings (Pins 1 and 8)
The voltage gain of the power amplifier is fixed by the internal resistors.
Pins 1 and 8 be left open : Approximately 26dB
Pins 1 and 8 connected to GND : Approximately 39.5dB
Note that the voltage gain can be changed using two resistors. (See Fig. 1)
Voltage gain setting : According to the resistor connected between Pin 8 and Pin 2 (GND1)
* Voltage gain = 20log (20
× (625 + Rvg1)/(125 + Rvg1))
Output DC voltage setting : According to the resistor connected between Pin 1 and Pin 2 (GND1)
* Rvg1 = Rvg2 must be satisfied.
In addition, the voltage gain can also be lowered to approximately 20dB (when using 5V or 6V power supply) by an
application such as shown in Fig. 2 below.
Voltage gain setting : According to the resistor connected between Pin 8 and Pin 5 (OUT)
* Voltage gain = 20log (20
× (125 + Rvg3)/(10,125 + Rvg3))
Output DC voltage setting : According to the resistor connected between Pin 1 and Pin 6 (VCC)
* Set the resistor values so that the Pin 5 (OUT) DC voltage is approximately half the supply voltage.
Example : When Rvg3 = 10k
Ω, Rvg4 = 22kΩ (when VCC = 6V)
However, note that using this method to greatly lower the voltage gain deteriorates the characteristics, so the voltage
gain should be lowered only to approximately 20dB. In addition, when using a high supply voltage (7V or more), the
clipped waveform may invert, so this voltage gain reduction method must not be used in these cases.
LA4815M
Rvg1
Rvg2
GAIN2
GAIN1
GND1
VCC
OUT
LA4815M
Rvg3
Rvg4
GAIN2
GAIN1
GND1
VCC
OUT
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
Figure 1
Figure 2
2. Signal source impedance : rg
The signal source impedance value rg affects the ripple rejection ratio together with input coupling capacitor Cin, so rg
should be as small as possible. Therefore, when attenuating the signal at the Cin front end as shown in Fig. 4, the
constants should be set in consideration of these characteristics. Using the smallest resistor Rg1 value possible is
recommended.
In addition, when setting the signal level, the voltage gain should be set on the LA4815M side and the input front-end
should be configured using only the input coupling capacitor, Cin, as shown in Fig. 5 in order to maximize the ripple
rejection ratio.
Vbias
100k
Ω
+
-
Pre-Amp
Rg2
Cin
Rg1
rg
OUT
other IC
ro
LA4815M
IN
Cin
other IC
ro
LA4815M
Cin
IN
3
OUT
IN
3
Figure 4
Figure 3
Figure 5
No.A1373-6/14
相關PDF資料 |
PDF描述 |
|---|---|
| LA4815M | 0.62 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LA4815 | 5 W, 2 CHANNEL, AUDIO AMPLIFIER, DIP28 |
| LA4815 | 5 W, 2 CHANNEL, AUDIO AMPLIFIER, DIP28 |
| LA4820M | 0.12 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO24 |
| LA4901 | 10 W, 1 CHANNEL, AUDIO AMPLIFIER, DIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA4815M_10 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monaural Power Amplifier |
| LA4815M-TLM-H | 功能描述:功率放大器 MONAURAL POWER AMPLIFIER RoHS:否 制造商:TriQuint Semiconductor 封裝 / 箱體: 工作電源電壓:28 V 電源電流:2.5 A 工作溫度范圍: 封裝: |
| LA4815VH | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monaural Power Amplifier |
| LA4815VH_12 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monaural Power Amplifier |
| LA4815VH-MPB-H | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。