- 您現在的位置：買賣IC網 > PDF目錄367511 > LB1048AG Voltage-Mode SMPS Controller PDF資料下載
參數資料
| 型號： | LB1048AG |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Voltage-Mode SMPS Controller |
| 中文描述： | 電壓模式開關電源控制器 |
| 文件頁數： | 7/24頁 |
| 文件大小： | 377K |
| 代理商： | LB1048AG |
Product Specification
7 / 24
LB104V03
Liquid Crystal Display
Ver. 1.1
Oct. 10, 2003
5. The output of the inverter must have symmetrical(negative and positive) voltage waveform and
symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter
which has unsymmetrical voltage and unsymmetrical current and spike wave.
Lamp frequency may produce interference with horizontal synchronous frequency and as a result this
may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal
synchronous frequency and from its harmonics in order to prevent interference.
6. Let’s define the brightness of the lamp after being lighted for 5 minutes as 100%.
T
is the time required for the brightness of the center of the lamp to be not less than 95%.
7. The lamp power consumption shown above does not include loss of external inverter for 2 CCFLs.
The used lamp current is the lamp typical current.
8. The life time is determined as the time at which brightness of the lamp is 50% compared to that of initial
value at the typical lamp current on condition of continuous operating at 25
±
2
°
C.
Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp, are following. It shall help increase the lamp lifetime and
reduce leakage current.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion rate of the waveform should be within
√
2
±
10%.
* Inverter output waveform had better be more similar to ideal sine wave.
Do not attach a conducting tape to lamp connecting wire.
If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter
has abnormal action. Because leakage current is occurred between lamp wire and conducting tape.
I
p
I
-p
* Asymmetry rate:
| I
p
– I
–p
| / I
rms
* 100%
* Distortion rate
I
p
(or I
–p
) / I
rms
3-2. Interface Connections
This LCD employs Three interface connections, a 30 pin connector is used for the module electronics interface
and the other connectors are used for the integral backlight system.
The electronics interface connector is a model KN10G-30S-1H manufactured by Hirose,
GT101-30S-H16 manufactured by LG Cable or equivalent.
(Mating connector: FI-X30M manufactured by JAE)
Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)
相關PDF資料 |
PDF描述 |
|---|---|
| LB1103 | |
| LB1108AD | Voltage-Feedback Operational Amplifier |
| LB1109AB | Isolation Amplifier |
| LB1100 | |
| LB1101 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB104S01-OF | 制造商:AIS 功能描述:AIS OPEN FRAME SOLUTION FOR PANEL LB104S01 - Bulk |
| LB104S01-TL01-OF | 制造商:AIS 功能描述:AIS OPEN FRAME - Bulk |
| LB104V03 | 制造商:NXP Semiconductors 功能描述: |
| LB104V03-A1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Liquid Crystal Display |
| LB104V03-A12-OF | 制造商:AIS 功能描述:AIS OPEN FRAME - Bulk |
發布緊急采購，3分鐘左右您將得到回復。