- 您現在的位置：買賣IC網 > PDF目錄30731 > LC72706E SPECIALTY CONSUMER CIRCUIT, PQFP44 PDF資料下載
參數資料
| 型號： | LC72706E |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| 封裝： | QFP-44 |
| 文件頁數： | 12/15頁 |
| 文件大小： | 164K |
| 代理商： | LC72706E |
No. 5745-6/15
LC72706E
Layer 4 CRC Data Input Timing
Serial Control Data Input Settings
The input data consists of 16 bits (DI0 to DI15). The upper 8 bits (DI8 to DI15) are the control address and the lower 8
bits (DI0 to DI7) are the input data. Bits DI12 to DI15 are ignored.
Number of Allowed BIC Errors
This IC’s synchronization circuit operates by recognizing a 16-bit BIC code. The number of allowed errors is the
number of allowed error bits in the 16 bits used for BIC recognition. This data item allows the forward protection mode
(used when synchronized) and the backward protection mode (used when not synchronized) values to be set
independently. The default value is to allow up to 2 error bits in both the forward and backward directions. We
recommend setting the backward protection mode number of allowable BIC errors to 1 or 0 if the block
synchronization recognition output (the BLOCK pin, pin 23) is used to recognize the presence or absence of FM
multiplex data.
Block Synchronization Error Protection Count
The synchronization protection count can be set independently in the forward and backward directions. The protection
count conditions are as follows.
— Backward protection (unsynchronized, BLOCK = low)
When the timing of the IC’s internal synchronization free-running counter matches that of the received BIC, the
protection count is incremented by 1. Similarly, if the IC internal counter and the received BIC do not match, the
counter is cleared to 0. The count timing is the timing of the IC internal counter.
— Forward protection (synchronized, BLOCK = high)
Operation is the opposite of the backward case, namely, the protection count is incremented when the timing of the
IC’s internal synchronization free-running counter does not match that of the received BIC, and the protection
count is cleared to zero when the timing matches.
Figure 1 shows the protection counter when both the forward and backward protection counts are set to 3. This IC
defines the protection counter value to be 1 at the point where a match or a mismatch occurs between the IC
internal timing and the received BIC timing. For example, a backward protection count of 2 corresponds to the case
where the IC internal timing and the received BIC timing match two times consecutively. To set the protection data
to new values, applications must send data in which 1 has been subtracted from the desired values, e.g. to set up
protection counts of 3 as shown in figure 1, applications must send the value 22H. Similarly, if the value set is 00,
due to the definition, the protection counts for both the forward and backward directions will be set to 1. However,
from an operation standpoint, this corresponds to operation equivalent to there being no protection circuit. The
default values are a forward protection count of 8 and a backward protection count of 2. We recommend resetting
the block synchronization backward protection count to a value more strict than the default,
CRC4 pin output
Note: The N items are 8-bit units.
CRC4 output after N items transferred
Register
Address
Data
Default
DI11
DI10
DI9
DI8
setting
Number of allowable BIC errors
0
Upper 4 bits
Allowed error bits backward
2
Lower 4 bits
Allowed error bits forward
2
Number of block error protection states
0
1
Upper 4 bits
Block backward protection
1
Lower 4 bits
Block forward protection
7
Number of frame error protection states
0
1
0
Upper 4 bits
Frame backward protection
1
Lower 4 bits
Frame forward protection
7
Control register
0
1
See the control register description on page 8.
相關PDF資料 |
PDF描述 |
|---|---|
| LC72707E | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC72708E | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC72708E | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC72709E | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC72709W | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72707 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Receiver IC Supporting All Worldwide Standards |
| LC72707E | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Receiver IC Supporting All Worldwide Standards |
| LC72708 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Broadcast Reception IC for Mobile VICS Systems |
| LC72708E | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Broadcast Reception IC for Mobile VICS Systems |
| LC72709 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:FM Multiplex Reception IC for Mobile Systems |
發布緊急采購，3分鐘左右您將得到回復。