- 您現在的位置：買賣IC網 > PDF目錄30731 > LC72714W SPECIALTY CONSUMER CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | LC72714W |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, SQFP-64 |
| 文件頁數： | 2/29頁 |
| 文件大小： | 158K |
| 代理商： | LC72714W |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
LC72714W
No.6871-10/29
Layer 4 CRC Register
Address
Register
R/W
Initial value
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
06H
CRC4
W
00H
(LSB)
This is the data group write register used for the layer 4 CRC check. It is used only when the parallel interface is used.
Applications should specify the dedicated CCB address when using the serial interface.
Status Register
Address
Register
R/W
Initial value
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
01H
STAT
R
-
VH
BLK
FRM
ERR
PRI
HEAD
CRC4
*
*: BIT0 is unused.
VH
0: Indicates data for which only horizontal correction was performed.
1: Indicates data for which after horizontal correction, vertical and then second horizontal correction were performed
as well.
BLK
0: Indicates data that was received with block synchronization unsynchronized.
1: Indicates data that was received with block synchronization synchronized.
FRM
0: Indicates data that was received with frame synchronization unsynchronized.
1: Indicates data that was received with frame synchronization synchronized.
ERR
0: Indicates data for which error correction completed and no errors were detected in the level 2 CRC check.
1: Indicates data for which error correction was not possible or for which errors were detected in the level 2 CRC
check.
PRI
0: Indicates data that was inferred to be data block data by the frame synchronization circuit.
1: Indicates data that was inferred to be parity block data by the frame synchronization circuit.
HEAD
0:
1: Indicates data that was inferred to be in the frame head block by the frame synchronization circuit.
This flag is valid only when VH is 0.
CRC4
0: Indicates that the layer 4 CRC detection circuit division registers were not all zeros.
1: Indicates that the layer 4 CRC detection circuit division registers were all zeros, i.e. that there were no errors.
The result at the point immediately prior to register readout is loaded into this flag.
Block Number Register
Address
Register
R/W
Initial value
BIT7
BIT6
BIT5
BIT4
BIT3
BIT2
BIT1
BIT0
02H
BLNO
R
-
BLN7
BLN6
BLN5
BLN4
BLN3
BLN2
BLN1
BLN0
Indicates the block number or the parity block number of the output data.
A single frame consists of data blocks numbered 0 to 189 and parity blocks numbered 0 to 81. Output following
vertical correction does not include parity block data.
The value of the block number register is undefined if VEC_HALT (bit 2 in control register 1) is set to 1.
相關PDF資料 |
PDF描述 |
|---|---|
| LC72715PW | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| LC72720NM | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC72720NM | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC72720N | SPECIALTY CONSUMER CIRCUIT, PDIP24 |
| LC72720N | SPECIALTY CONSUMER CIRCUIT, PDIP24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72715PW | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| LC72717PW | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Mobile FM Multiplex Broadcast (DARC) Receiver IC |
| LC72720 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip RDS Signal-Processing System LSI |
| LC72720M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip RDS Signal-Processing System LSI |
| LC72720N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip RDS Signal-Processing System LSI |
發布緊急采購，3分鐘左右您將得到回復。