欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: LC74772V
元件分類: 畫面疊加
英文描述: ON-SCREEN DISPLAY IC, PDSO24
封裝: SSOP-24
文件頁數: 15/17頁
文件大小: 173K
代理商: LC74772V
x COMMAND 0 (System control setup 1)
First byte
Notes on command settings
1. RSTSYS: A command reset is executed immediately after the data is read.
The reset is cleared by returning the CS pin to high to reset this register. The reset is also cleared if this command is
executed consecutively or if this register is set to 0.
2. RAMCLR: The RAM can only be erased when display is off. This operation is not executed during display. This
operation cannot be executed if the LC oscillator is stopped. Only use this command when the LC oscillator is
operating.
This command bit is automatically cleared when the RAM erase operation completes.
Once the RAM erase command has been read in, the following time is required to complete the operation.
— Tclear = 5 [s] + 4/fOSC (LC-oscillator) × 288
3. OSCSTP: The LC oscillator stop command stops the LC oscillator connected to pins 2 and 3 (OSCIN and OSCOUT).
The oscillator stop command is only executed when display is off. It is not executed if display is in progress.
In external clock input mode, this command stops the acquisition of that clock signal.
4. TSTMOD: The test mode command is executed if the TESTIN pin (pin 5) is high. This command should not be used
by applications in normal operation.
Note: This register is set to 0 on a reset (either by the RST pin or by a command reset).
No. 5159-7/17
LC74772V
Register content
DA0 to DA7
Register name
State
Function
Note
7
0
6
0
Command 0 identification code
5
0
4
0
3
RST
0
Normal operation
If CS is low, the reset is executed, but if
SYS
1
System reset
CS is high this command will be excluded.
RAM
0
Normal operation
The VRAM clear operation is not
2
executed when the oscillator
CLR
1
Normal operation VRAM clear (All data is set to FE (hexadecimal)) is stopped.
OSC
0
The LC oscillator operating state is maintained.
Valid when the display is off. VRAM write
1
is not possible when the oscillator is
STP
1
The LC oscillator is stopped.
stopped.
0
TST
0
Normal operation
Illegal setting.
MOD
1
Test mode
This bit must always be set to 0.
相關PDF資料
PDF描述
LC74772V ON-SCREEN DISPLAY IC, PDSO24
LC74776 ON-SCREEN DISPLAY IC, PDIP30
LC74776M ON-SCREEN DISPLAY IC, PDSO30
LC74776M ON-SCREEN DISPLAY IC, PDSO30
LC74780M ON-SCREEN DISPLAY IC, PDSO24
相關代理商/技術參數
參數描述
LC74772V_99 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Camcorder On-Screen Display LSI
LC74772V-9015-E 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
LC74772V-9015-TLM-E 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
LC74772VH-9015-TLM-E 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
LC74775 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:On-Screen Display Controller IC
主站蜘蛛池模板: 金昌市| 磐安县| 镇远县| 白银市| 长寿区| 瓮安县| 左贡县| 镇康县| 普定县| 茌平县| 元江| 河池市| 道孚县| 平原县| 油尖旺区| 昭通市| 瑞安市| 阳新县| 牙克石市| 宝兴县| 葫芦岛市| 平南县| 玛曲县| 莫力| 永和县| 七台河市| 大田县| 沁阳市| 新建县| 岳西县| 扎兰屯市| 阿坝| 海兴县| 富平县| 仁寿县| 临沭县| 临猗县| 镇康县| 阿尔山市| 米林县| 阜新市|