- 您現在的位置：買賣IC網 > PDF目錄30736 > LC78630E SPECIALTY CONSUMER CIRCUIT, PQFP80 PDF資料下載
參數資料
| 型號： | LC78630E |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 11/33頁 |
| 文件大小： | 432K |
| 代理商： | LC78630E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
FSX is a 7.35 kHz frame synchronization signal generated by dividing the crystal clock. The error correction state for
each frame is output from EFLG. EFLG indicates the C1 correction state while FSX is high and the C2 correction
state while FSX is low. The playback OK/NG state can be easily determined from the number of high levels that
appear here.
Note: The FSX polarity is opposite in the LC78620 and LC7860 Series LSIs.
9. Subcode P, Q, and R to W output circuit; Pin 62: PW, pin 60: SBSY, pin 63: SFSY, pin 64: SBCK
PW is the subcode signal output pin, and all the codes, P, Q, and R to W can be read out by sending eight clocks to
the SBCK pin within 136 s after the fall of SFSY. The signal that appears on the PW pin changes on the rising edge
of SBCK. If a clock is not applied to SBCK, the P code will be output from PW. SFSY is a signal that is output for
each subcode frame cycle, and the falling edge of this signal indicates standby for the output of the subcode symbol
(P to W). Subcode data P is output on the fall of this signal.
SBSY is a signal output for each subcode block. This signal goes high for the S0 and S1 synchronizing signals. The
fall of this signal indicates the end of the subcode synchronizing signals and the start of the data in the subcode
block. (EIAJ format)
10. Subcode Q output circuit; Pin 67: WRQ, pin 68: RWC, pin 69: SQOUT, pin 71: CQCK, pin 78: CS
Subcode Q can be read from the SQOUT pin by applying a clock to the CQCK pin.
Of the eight bits in the subcode, the Q signal is used for song (track) access and display. The WRQ will be high only
if the data passed the CRC error check and the subcode Q format internal address is 1*. The control microprocessor
can read out data from SQOUT in the order shown below by detecting this high level and applying CQCK. When
CQCK is applied the DSP disables register update internally. The microprocessor should give update permission by
setting RWC high briefly after reading has completed. WRQ will fall to low at this time. Since the WRQ high period
is 11.2 ms, CQCK must be applied during the high period. Note that data is read out in an LSB first format.
Note: If RWC is set high by command while WRQ is high, WRQ will return to low and the SQOUT data will be
invalid.
Note: * This state will be ignored if an address free command is sent.
No. 5121-19/33
LC78630E
Code
Command
RES = low
$09
ADDRESS FREE
$89
ADDRESS 1
r
相關PDF資料 |
PDF描述 |
|---|---|
| LC78631E | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| LC78637E | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| LC78647NT | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| LC78648E | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| LC78681E | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC78631 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Compact Disk Player DSP |
| LC78631E | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Compact Disk Player DSP |
| LC78632 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Compact Disk Player DSP |
| LC78632RE | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Compact Disk Player DSP |
| LC78637E-E | 制造商:ON Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。