- 您現在的位置：買賣IC網 > PDF目錄30737 > LC85632 LED CLOCK, PDIP30 PDF資料下載
參數資料
| 型號： | LC85632 |
| 元件分類： | 時鐘及定時 |
| 英文描述： | LED CLOCK, PDIP30 |
| 封裝： | DIP-30 |
| 文件頁數： | 24/34頁 |
| 文件大小： | 394K |
| 代理商： | LC85632 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
LC85632
Self Test Mode
* TEST [Pin 18]
VSS
OPEN
VDD
LED self test mode
Normal operation
IC test, illegal setting
This IC provides a self-test mode for testing the LED display and the three value input pins. It supports the following
tests.
The LEDs can be tested for failure to light and for unbalanced intensity.
This test mode is entered when a low level is applied to the TEST pin (pin 18), and all LED segments are lit. In this state,
the LED segments can be turned off individually by applying high or low levels to the three value input pins. The
correspondence between the applied inputs and the segments that are turned off is shown in the table below.
Input pin
Input level
Corresponding LED segment*1
RT-TIME SET
High level
a segment*2
TIME SET INPUT
High level
b segment
TIME SET INPUT
Low level
c segment
ALM-A/B DISP & SEL
High level
d segment*2
ALM-A/B DISP & SEL
Low level
e segment
MANUAL & SLEEP
High level
f segment
MANUAL & SLEEP
Low level
g segment
CAL DISP & SNOOZE
Both*3
COLON
RT-TIME SET
Low level
AM, PM, ALM-A, ALM-B
Note: 1. The LED segments are lit or turned off at the same time for all digits. For example, after setting the IC to LED test mode, if a high level is applied to
the TIME SET INPUT pin, then all 4 a segments (one LED in each 4 digits) are turned off.
2. Due to details of the output pins only the 10’SHR d segment is not linked to rest of the d segment, but is turned off an on along with the a segment.
3. Operates identically for both high and low level signals.
4. Since the operations in the above table are toggle operations, repeated application of signals to the three value inputs will repeatedly turn each
segment on and off.
5. When the IC is in the LED test mode, the MODE SELECT pin must be held at either the high, open, or low level. Operation of the IC is not
guaranteed if the signal on the MODE SELECT pin changes while the IC is in the LED test mode.
6. The TEST pin must be left open during normal operation.
7. Do not change the setting on the MODE SELECT pin (pin 28) when the IC in self test mode. System operation is not guaranteed if this setting is
changed.
No. 4659-30/34
相關PDF資料 |
PDF描述 |
|---|---|
| LC8650T | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC8900KQ | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC8901 | SPECIALTY CONSUMER CIRCUIT, PDIP42 |
| LC8901Q | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| LC8902 | SPECIALTY CONSUMER CIRCUIT, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC85A | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:TRANSIENT ABSORPTION ZENER |
| LC86104 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC86104A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:168bytes RAM 8-BIT SINGLE CHIP MICROCOMPUTER |
| LC86104C | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:On-chip 168 Bytes RAM 8-BIT SINGLE CHIP MICROCOMPUTER |
| LC86108 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。