- 您現在的位置：買賣IC網 > PDF目錄30744 > LM1881N-X/NOPB (NATIONAL SEMICONDUCTOR CORP) SYNC SEPARATOR IC, PDIP8 PDF資料下載
參數資料
| 型號： | LM1881N-X/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 信號分離 |
| 英文描述： | SYNC SEPARATOR IC, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 7/12頁 |
| 文件大小： | 688K |
| 代理商： | LM1881N-X/NOPB |
Typical Performance Characteristics (Continued)
Vertical Pulse
Width vs Temperature
Supply Current vs
Supply Voltage
00915011
00915002
Application Notes
The LM1881 is designed to strip the synchronization signals
from composite video sources that are in, or similar to, the
N.T.S.C. format. Input signals with positive polarity video
(increasing signal voltage signifies increasing scene bright-
ness) from 0.5V (p-p) to 2V (p-p) can be accommodated.
The LM1881 operates from a single supply voltage between
5V DC and 12V DC. The only required external components
besides a power supply decoupling capacitor at pin 8 and a
set current decoupling capacitor at pin 6, are the composite
input coupling capacitor at pin 2 and one resistor at pin 6 that
sets internal current levels. The resistor on pin 6 (i.e. R
set)
allows the LM1881 to be adjusted for source signals with line
scan frequencies differing from 15.734 kHz. Four major sync
signals are available from the I/C; composite sync including
both horizontal and vertical scan timing information; a verti-
cal sync pulse; a burst gate or back porch clamp pulse; and
an odd/even output. The odd/even output level identifies
which video field of an interlaced video source is present at
the input. The outputs from the LM1881 can be used to
gen-lock video camera/VTR signals with graphics sources,
provide identification of video fields for memory storage,
recover suppressed or contaminated sync signals, and pro-
vide timing references for the extraction of coded or uncoded
data on specific video scan lines.
To better understand the LM1881 timing information and the
type of signals that are used, refer to Figure 1(a-e) which
shows a portion of the composite video signal from the end
of one field through the beginning of the next field.
COMPOSITE SYNC OUTPUT
The composite sync output, Figure 1(b), is simply a repro-
duction of the signal waveform below the composite video
black level, with the video completely removed. This is ob-
tained by clamping the video signal sync tips to 1.5V DC at
Pin 2 and using a comparator threshold set just above this
voltage to strip the sync signal, which is then buffered out to
Pin 1. The threshold separation from the clamped sync tip is
nominally 70 mV which means that for the minimum input
level of 0.5V (p-p), the clipping level is close to the halfway
point on the sync pulse amplitude (shown by the dashed line
on Figure 1(a). This threshold separation is independent of
the signal amplitude, therefore, for a 2V (p-p) input the
clipping level occurs at 11% of the sync pulse amplitude. The
charging current for the input coupling capacitor is 0.8 mA,
Normally the signal source for the LM1881 is assumed to be
clean and relatively noise-free, but some sources may have
excessive video peaking, causing high frequency video and
chroma components to extend below the black level refer-
ence. Some video discs keep the chroma burst pulse
present throughout the vertical blanking period so that the
burst actually appears on the sync tips for three line periods
instead of at black level. A clean composite sync signal can
be generated from these sources by filtering the input signal.
When the source impedance is low, typically 75
, a 620
resistor in series with the source and a 510 pF capacitor to
ground will form a low pass filter with a corner frequency of
500 kHz. This bandwidth is more than sufficient to pass the
sync pulse portion of the waveform; however, any subcarrier
content in the signal will be attenuated by almost 18 dB,
effectively taking it below the comparator threshold. Filtering
will also help if the source is contaminated with thermal
noise. The output waveforms will become delayed from be-
tween 40 ns to as much as 200 ns due to this filter. This
much delay will not usually be significant but it does contrib-
ute to the sync delay produced by any additional signal
processing. Since the original video may also undergo pro-
cessing, the need for time delay correction will depend on
the total system, not just the sync stripper.
VERTICAL SYNC OUTPUT
A vertical sync output is derived by internally integrating the
composite sync waveform (Figure 2). To understand the
generation of the vertical sync pulse, refer to the lower left
hand section Figure 2. Note that there are two comparators
in the section. One comparator has an internally generated
voltage reference called V
1 going to one of its inputs. The
other comparator has an internally generated voltage refer-
LM1881
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| LM1882-RCMX | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 54ACT715-RD | SPECIALTY CONSUMER CIRCUIT, CDIP20 |
| 54ACT715D | SPECIALTY CONSUMER CIRCUIT, CDIP20 |
| 54ACT715-RLX | SPECIALTY CONSUMER CIRCUIT, CQCC20 |
| 54ACT715-RL | SPECIALTY CONSUMER CIRCUIT, CQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1881-X | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM1881 Video Sync Separator |
| LM1882 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Programmable Video Sync Generator |
| LM1882CM | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LM1882CN | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Programmable Video Sync Generator |
| LM1882-R | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Programmable Video Sync Generator |
發布緊急采購，3分鐘左右您將得到回復。