欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: LM1882D
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, CDIP20
封裝: CERAMIC, DIP-20
文件頁數: 3/19頁
文件大小: 383K
代理商: LM1882D
Capacitance (Continued)
Additional Applications Information
POWERING UP
The ’ACT715/LM1882 default value for Bit 10 of the Status
Register is 0. This means that when the CLEAR pulse is ap-
plied and the registers are initialized by loading the default
values the CLOCK is disabled. Before operation can begin,
Bit 10 must be changed toa1to enable CLOCK. If the de-
fault values are needed (no other programming is required)
then
Figure 6 illustrates a hardwired solution to facilitate the
enabling of the CLOCK after power-up. Should control sig-
nals be difficult to obtain,
Figure 7 illustrates a possible solu-
tion to automatically enable the CLOCK upon power-up. Use
of the ’ACT715-R/LM1882-R eliminates the need for most of
this circuitry. Modifications of the
Figure 7 circuit can be
made to obtain the lone CLEAR pulse still needed upon
power-up.
Note that, although during a Vectored Restart none of the
preprogrammed registers are affected, some signals are af-
fected for the duration of one frame only. These signals are
the Horizontal and Vertical Drive signals. After a Vectored
Restart the beginning of these signals will occur at the first
CLK. The end of the signals will occur as programmed. At
the completion of the first frame, the signals will resume to
their programmed start and end time.
PREPROGRAMMING “ON-THE-FLY”
Although the ’ACT715/LM1882 and ’ACT715-R/LM1882-R
are completely programmable, certain limitations must be
set as to when and how the parts can be reprogrammed.
Care must be taken when reprogramming any End Time reg-
isters to a new value that is lower than the current value.
Should the reprogramming occur when the counters are at a
count after the new value but before the old value, then the
counters will continue to count up to 4096 before rolling over.
For this reason one of the following two precautions are rec-
ommended when reprogramming “on-the-fly”. The first rec-
ommendation is to reprogram horizontal values during the
horizontal blank interval only and/or vertical values during
the vertical blank interval only. Since this would require deli-
cate timing requirements the second recommendation may
be more appropriate.
The second recommendation is to program a Vectored Re-
start as the final step of reprogramming. This will ensure that
all registers are set to the newly programmed values and
that all counters restart at the first CLK position. This will
avoid overrunning the counter end times and will maintain
the video integrity.
DS100232-6
FIGURE 5. AC Specifications
www.national.com
11
相關PDF資料
PDF描述
LM1882L SPECIALTY CONSUMER CIRCUIT, CQCC20
LM1882P SPECIALTY CONSUMER CIRCUIT, PDIP20
LM1882S SPECIALTY CONSUMER CIRCUIT, PDSO20
LM1882E/883 SPECIALTY CONSUMER CIRCUIT, CQCC20
LM1882J/883 SPECIALTY CONSUMER CIRCUIT, CDIP20
相關代理商/技術參數
參數描述
LM1882-R 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Programmable Video Sync Generator
LM1882RCM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TV/Video Sync Circuit
LM1882-RCM 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Programmable Video Sync Generator
LM1882RCN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TV/Video Sync Circuit
LM1882-RCN 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Programmable Video Sync Generator
主站蜘蛛池模板: 定安县| 永丰县| 朔州市| 博客| 洞头县| 海林市| 安国市| 西城区| 通海县| 鄢陵县| 娄烦县| 尼勒克县| 砚山县| 阜宁县| 贡嘎县| 寿阳县| 龙南县| 德保县| 密云县| 保定市| 金门县| 耒阳市| 陈巴尔虎旗| 治县。| 札达县| 临潭县| 昌江| 宁城县| 土默特右旗| 金昌市| 云林县| 武山县| 那坡县| 邹平县| 新安县| 阜新| 祥云县| 吉安市| 河曲县| 芒康县| 宣城市|