- 您現在的位置：買賣IC網 > PDF目錄30744 > LM1894MDC (NATIONAL SEMICONDUCTOR CORP) SPECIALTY CONSUMER CIRCUIT, UUC PDF資料下載
參數資料
| 型號： | LM1894MDC |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, UUC |
| 封裝： | DIE |
| 文件頁數： | 6/12頁 |
| 文件大小： | 345K |
| 代理商： | LM1894MDC |
Electrical Characteristics (Continued)
V
S = 8V, TA = 25C, VIN = 300 mV at 1 kHz, circuit shown in Figure 1 unless otherwise specified
Parameter
Conditions
Min
Typ
Max
Units
CONTROL SIGNAL PATH
Peak Detector Input Impedance
Pin 9
560
700
840
Voltage Gain
Pin 9 to Pin 10
30
33
36
V/V
Attack Time
Measured to 90% of Final Value
300
500
700
s
with 10 kHz Tone Burst
Decay Time
Measured to 90% of Final Value
45
60
75
ms
with 10 kHz Tone Burst
DC Voltage Range
Minimum Bandwidth to Maximum
1.1
3.8
V
Bandwidth
Note 2: For operation in ambient temperature above 25C, the device must be derated based on a 150C maximum junction temperature and a thermal resistance
of 1) 80C/W junction to ambient for the dual-in-line package, 2) 105C/W junction to ambient for the small outline package, and 3) 150C/W junction to ambient for
the TSSOP package.
Note 3: To force the DNR system into maximum bandwidth, DC ground the input to the peak detector, pin 9. A negative temperature coefficient of 0.5%/C on the
bandwidth, reduces the maximum bandwidth at increased ambient temperature or higher package dissipation. AC ground pin 9 or pin 6 to select minimum
bandwidth. To change minimum and maximum bandwidth, see Appliction Hints.
Note 4: The maximum noise reduction CCIR/ARM weighted is about 14 dB. This is accomplished by changing the bandwidth from maximum to minimum. In actual
operation, minimum bandwidth is not selected, a nominal minimum bandwidth of about 2 kHz gives 10 dB of noise reduction. See Application Hints.
Note 5: The CCIR/ARM weighted noise is measured with a 40 dB gain amplifier between the DNR system and the CCIR weighting filter; it is then input referred.
Note 6: Measured using the Rhode-Schwartz psophometer.
Note 7: Pin 10 is DC forced half way between the maximum bandwidth DC level and minimum bandwidth DC level. An AC 1 kHz signal is then applied to pin 10.
Its peak-to-peak amplitude is VDC (max BW) VDC (min BW).
Typical Performance Characteristics
Supply Current vs
Supply Voltage
DS007918-13
Channel Separation
(Referred to the Output)
vs Frequency
DS007918-14
Power Supply Rejection
Ratio (Referred to the
Output) vs Frequency
DS007918-15
THD vs Frequency
DS007918-16
3 dB Bandwidth
vs Frequency and
Control Signal
DS007918-17
Gain of Control Path
vs Frequency (with
10 kHz FM Pilot Filter)
DS007918-18
LM1894
www.national.com
3
相關PDF資料 |
PDF描述 |
|---|---|
| LM1894MWC | SPECIALTY CONSUMER CIRCUIT, UUC |
| LM1894MT/NOPB | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| LM1894MTX/NOPB | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| LM1897N | 2 CHANNEL, AUDIO AMPLIFIER, PDIP16 |
| LM1971-NRE | SPECIALTY CONSUMER CIRCUIT, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1894MT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LM1894MTBD | 功能描述:BOARD EVALUATION LM1894 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| LM1894MX | 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| LM1894MX/NOPB | 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| LM1894N | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:OC White Company 功能描述:Dynamic Noise Reduction System 14-Pin PDIP Rail |
發布緊急采購，3分鐘左右您將得到回復。