- 您現在的位置：買賣IC網 > PDF目錄30744 > LM1972MNOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY CONSUMER CIRCUIT, PDSO20 PDF資料下載
參數資料
| 型號： | LM1972MNOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 封裝： | SOP-20 |
| 文件頁數： | 6/12頁 |
| 文件大小： | 406K |
| 代理商： | LM1972MNOPB |
Timing Diagram
1197803
FIGURE 2. Timing Diagram
Pin Descriptions
Signal Ground (3, 19):
Each input has its own independent
ground, GND1 and GND2.
Signal Input (4, 20):
There are 2 independent signal inputs,
IN1 and IN2.
Signal Output (2, 17):
There are 2 independent signal out-
puts, OUT1 and OUT2.
Voltage Supply (13, 15):
Positive voltage supply pins,
V
DD1 and VDD2.
Voltage Supply (7, 18):
Negative voltage supply pins, V
SS1
and V
SS2. To be tied to ground in a single supply configuration.
AC Ground (1, 5, 6, 14, 16):
These five pins are not physi-
cally connected to the die in any way (i.e., No bondwires).
These pins must be AC grounded to prevent signal coupling
between any of the pins nearby. Pin 14 should be connected
to pins 13 and 15 for ease of wiring and the best isolation, as
an example.
Logic Ground (8):
Digital signal ground for the interface
lines; CLOCK, LOAD/SHIFT, DATA-IN and DATA-OUT.
Clock (9):
The clock input accepts a TTL or CMOS level sig-
nal. The clock input is used to load data into the internal shift
register on the rising edge of the input clock waveform.
Load/Shift (10):
The load/shift input accepts a TTL or CMOS
level signal. This is the enable pin of the device, allowing data
to be clocked in while this input is low (0V).
Data-In (11):
The data-in input accepts a TTL or CMOS level
signal. This pin is used to accept serial data from a micro-
controller that will be latched and decoded to change a
channel's attenuation level.
Data-Out (12):
This pin is used in daisy-chain mode where
more than one
μPot is controlled via the same data line. As
the data is clocked into the chain from the
μC, the preceding
data in the shift register is shifted out the DATA-OUT pin to
the next
μPot in the chain or to ground if it is the last μPot in
the chain. The LOAD/SHIFT line goes high once all of the new
data has been shifted into each of its respective registers.
Connection Diagram
1197804
3
www.national.com
LM1972
相關PDF資料 |
PDF描述 |
|---|---|
| LM1972NNOPB | SPECIALTY CONSUMER CIRCUIT, PDIP20 |
| LM1972N/NOPB | SPECIALTY CONSUMER CIRCUIT, PDIP20 |
| LM1973N/NOPB | SPECIALTY CONSUMER CIRCUIT, PDIP20 |
| LM2005T | 11 W, 2 CHANNEL, AUDIO AMPLIFIER, PSFM11 |
| LM20333AMHX | 6 A SWITCHING REGULATOR, 240 kHz SWITCHING FREQ-MAX, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1972MX | 功能描述:衰減器 -IC RoHS:否 制造商:Skyworks Solutions, Inc. 最大衰減:18 dB 容差: 阻抗: 功率額定值:30 dBm 安裝風格:SMD/SMT 工作溫度范圍:- 40 C to + 85 C |
| LM1972MX/NOPB | 功能描述:有源衰減器 RoHS:否 制造商:TriQuint Semiconductor 通道數量: 最大頻率: 阻抗: 最大 VSWR: 位數: 最大工作溫度: 最小工作溫度: |
| LM1972N | 功能描述:IC AUDIO ATTENUATOR 2CH 20-DIP RoHS:否 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:- 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6 |
| LM1972N | 制造商:Texas Instruments 功能描述:AUDIO ATTENUATOR 78DB 1972 DIP20 |
| LM1972N/NOPB | 制造商:Texas Instruments 功能描述:Digital Attenuator 104dB Attenuation 20-Pin PDIP Rail |
發布緊急采購，3分鐘左右您將得到回復。