- 您現在的位置：買賣IC網 > PDF目錄30745 > LM2202N/NOPB (NATIONAL SEMICONDUCTOR CORP) 1 CHANNEL, VIDEO AMPLIFIER, PDIP20 PDF資料下載
參數資料
| 型號： | LM2202N/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDIP20 |
| 封裝： | N20A |
| 文件頁數： | 4/17頁 |
| 文件大小： | 416K |
| 代理商： | LM2202N/NOPB |
Circuit Description (Continued)
Applications
SINGLE VIDEO CHANNEL
A typical application for a single video channel is shown in
Figure 9. The video signal is AC coupled to pin 6. The
LM2202 internally biases the video signal to 2.6 V
DC. Con-
trast control is achieved by applying a 0V to 4V DC voltage
at pin 8. The amplifier’s gain is minimum (i.e., maximum sig-
nal attenuation) if pin 8 is at 0V and is maximum if pin 8 is at
4V. With pin 9 (drive control) at 0V, the amplifier has a maxi-
mum gain of 10.
For DC restoration, a clamp signal must be applied to the
clamp gate input (pin 14). The clamp signal should be logic
low (less than 0.8V) only during the back porch (black level
reference period) interval (see
Figure 2). The clamp gate in-
put is TTL compatible. Brightness control is provided by ap-
plying a 0V to 4V DC voltage at pin 19. For example, if pin 19
is biased at 1V then the video signal’s black level will be
clamped at 1V. A 510
load resistor is connected from the
video output pin (pin 17) to ground. This resistor biases the
output stage of the amplifier. For power dissipation consider-
ations, the load resistor should not be much less than 510
.
RGB VIDEO PREAMPLIFIER
Figure 10 shows an RGB video preamplifier circuit using
three LM2202s. Note that pins 1 and 2 of IC1 are connected
to pins 1 and 2 of IC2 and IC3 respectively. This allows IC1
to provide a master contrast control and optimum contrast
tracking. Adjusting the contrast voltage at pin 8 of IC1 will
vary the gain of all three video channels. Drive control input
(pin 9) of each LM2202 allows individual gain adjustment for
achieving white balance.
The black level of each video channel can be individually ad-
justed to the desired voltage by adjusting the voltage at pin
19. In a DC-coupled cathode drive application, adjusting the
voltage at pin 19 of each IC will provide cutoff adjustment. In
an AC-coupled cathode drive application, the video signal is
AC coupled and DC restored at the cathode. In such an ap-
plication, the video signal’s black level may be clamped to
the desired level by simply biasing pin 19 to the black level
voltage by using a voltage divider at pin 19.
DS012591-14
FIGURE 8. Simplified Schematic of the LM2202 Clamp Comparator Circuit
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM2202M/NOPB | 1 CHANNEL, VIDEO AMPLIFIER, PDSO20 |
| LM22672QMR-ADJ | 1.8 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| LM236ZT | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PBCY3 |
| LM236DT | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PDSO8 |
| LM236Z-AP | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PBCY3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM220K12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LM220K15 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LM220K5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LM2-20V2-SI | 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel |
| LM220Z | 制造商:SEOUL 制造商全稱:Seoul Semiconductor 功能描述:GREEN OVAL LAMP LED |
發布緊急采購，3分鐘左右您將得到回復。