- 您現在的位置：買賣IC網 > PDF目錄361024 > LM2598 (National Semiconductor Corporation) SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator, with Features PDF資料下載
參數資料
| 型號： | LM2598 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator, with Features |
| 中文描述： | SIMPLE SWITCHER系列電源轉換器150千赫1A步降穩壓器的功能， |
| 文件頁數： | 15/33頁 |
| 文件大小： | 847K |
| 代理商： | LM2598 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
LM2598 Series Buck Regulator Design Procedure (Adjustable Output)
(Continued)
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
6. Input Capacitor (C
IN
)
Alow ESR aluminum or tantalum bypass capacitor is needed
between the input pin and ground to prevent large voltage
transients from appearing at the input. In addition, the RMS
current rating of the input capacitor should be selected to be
at least
1
2
the DC load current. The capacitor manufacturers
data sheet must be checked to assure that this current rating
is not exceeded. The curve shown in Figure 16shows typical
RMS current ratings for several different aluminum electro-
lytic capacitor values.
This capacitor should be located close to the IC using short
leads and the voltage rating should be approximately 1.5
times the maximum input voltage.
If solid tantalum input capacitors are used, it is recomended
that they be surge current tested by the manufacturer.
Use caution when using a high dielectric constant ceramic
capacitor for input bypassing, because it may cause severe
ringing at the V
IN
pin.
6. Input Capacitor (C
IN
)
The important parameters for the Input capacitor are the
input voltage rating and the RMS current rating. With a
nominal input voltage of 28V, an aluminum electrolytic alumi-
num electrolytic capacitor with a voltage rating greater than
42V (1.5 x V
IN
) would be needed. Since the the next higher
capacitor voltage rating is 50V, a 50V capacitor should be
used. The capacitor voltage rating of (1.5 x V
IN
) is a conser-
vative guideline, and can be modified somewhat if desired.
The RMS current rating requirement for the input capacitor of
a buck regulator is approximately
1
2
the DC load current. In
this example, with a 1A load, a capacitor with a RMS current
rating of at least 500 mA is needed.
The curves shown in Figure 16 can be used to select an
appropriate input capacitor. From the curves, locate the 50V
line and note which capacitor values have RMS current
ratings greater than 500 mA. Either a 100 μF or 120 μF, 50V
capacitor could be used.
For a through hole design, a 120 μF/50V electrolytic capaci-
tor (Panasonic HFQ series or Nichicon PL series or equiva-
lent) would be adequate. Other types or other manufacturers
capacitors can be used provided the RMS ripple current
ratings are adequate.
For surface mount designs, solid tantalum capacitors can be
used, but caution must be exercised with regard to the
capacitor surge current rating (see Application Information or
input capacitors in this data sheet). The TPS series available
from AVX, and the 593D series from Sprague are both surge
current tested.
For additional information, see section on input capaci-
tor in application information section.
To further simplify the buck regulator design procedure, Na-
tional Semiconductor is making available computer design
software to be used with the Simple Switcher line ot switch-
ing regulators.
Switchers Made Simple
(version 4.2 or later)
is available on a 3
1
2
" diskette for IBM compatible computers.
Output
Voltage
(V)
Through Hole Electrolytic Output Capacitor
Panasonic
Nichicon PL
HFQ Series
Series
(μF/V)
(μF/V)
330/50
330/50
220/25
220/25
220/25
220/25
180/25
180/25
120/25
120/25
120/25
120/25
82/35
82/35
82/50
82/50
Surface Mount Tantalum Output Capacitor
AVX TPS
Sprague
Series
595D Series
(μF/V)
(μF/V)
330/6.3
330/6.3
220/10
220/10
220/10
220/10
100/16
180/16
68/20
120/20
68/20
100/20
33/25
33/35
10/35
33/35
Feedforward
Capacitor
Feedforward
Capacitor
1.2
4
6
9
1 2
1 5
2 4
2 8
0
0
4.7 nF
3.3 nF
1.5 nF
1.5 nF
1.5 nF
1 nF
1 nF
4.7 nF
3.3 nF
1.5 nF
1.5 nF
1.5 nF
220 pF
220 pF
FIGURE 3. Output Capacitor and Feedforward Capacitor Selection Table
L
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| LM2598S-5.0 | SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator, with Features |
| LM2598S-12 | SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator, with Features |
| LM2598S-3.3 | SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator, with Features |
| LM2598S-ADJ | SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator, with Features |
| LM2599S-12 | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2598S-12 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2598S-12/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2598S12P+ | 制造商:Texas Instruments 功能描述: |
| LM2598S-12P+ | 制造商:Texas Instruments 功能描述:2.6 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, PSSO7 |
| LM2598S-3.3 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。