- 您現在的位置：買賣IC網 > PDF目錄361024 > LM2599S-5.0 (NATIONAL SEMICONDUCTOR CORP) SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features PDF資料下載
參數資料
| 型號： | LM2599S-5.0 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| 中文描述： | 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, PSSO7 |
| 封裝： | TO-263, 7 PIN |
| 文件頁數： | 18/31頁 |
| 文件大小： | 812K |
| 代理商： | LM2599S-5.0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Block Diagram
Application Information
PIN FUNCTIONS
+V
(Pin 1)— This is the positive input supply for the IC
switching regulator. A suitable input bypass capacitor must
be present at this pin to minimize voltage transients and to
supply the switching currents needed by the regulator.
Ground
(Pin 4)— Circuit ground.
Output
(Pin 2)— Internal switch. The voltage at this pin
switches between approximately (+V
IN
V
SAT
) and approxi-
mately 0.5V, with a duty cycle of V
OUT
/V
IN
. To minimize
coupling to sensitive circuitry, the PC board copper area con-
nected to this pin should be kept to a minimum.
Feedback
(Pin 6)— Senses the regulated output voltage to
complete the feedback loop.
Shutdown /Soft-start
(Pin 7)— This dual function pin pro-
vides the following features: (a) Allows the switching regula-
tor circuit to be shut down using logic level signals thus drop-
ping the total input supply current to approximately 80 μA.
(b) Adding a capacitor to this pin provides a soft-start feature
which minimizes startup current and provides a controlled
ramp up of the output voltage.
Error Flag
(Pin 3)— Open collector output that provides a
low signal (flag transistor ON) when the regulated output
voltage drops more than 5% from the nominal output volt-
age. On start up, Error Flag is low until V
reaches 95% of
the nominal output voltage and a delay time determined by
the Delay pin capacitor. This signal can be used as a reset to
a microprocessor on power-up.
Delay
(Pin 5)— At power-up, this pin can be used to provide
a time delay between the time the regulated output voltage
reaches 95% of the nominal output voltage, and the time the
error flag output goes high.
Special Note
If any of the above three features (Shutdown
/Soft-start, Error Flag, or Delay) are not used, the respective
pins should be left open.
EXTERNAL COMPONENTS
SOFT-START CAPACITOR
C
— A capacitor on this pin provides the regulator with a
Soft-start feature (slow start-up). When the DC input voltage
is first applied to the regulator, or when the Shutdown
/Soft-start pin is allowed to go high, a constant current (ap-
proximately 5 μA begins charging this capacitor). As the ca-
pacitor voltage rises, the regulator goes through four operat-
ing regions (See the bottom curve in Figure 13).
1. Regulator in Shutdown.
When the SD /SS pin voltage is
between 0V and 1.3V, the regulator is in shutdown, the out-
put voltage is zero, and the IC quiescent current is approxi-
mately 85 μA.
2. Regulator ON, but the output voltage is zero.
With the
SD /SS pin voltage between approximately 1.3V and 1.8V,
the internal regulator circuitry is operating, the quiescent cur-
rent rises to approximately 5 mA, but the output voltage is
still zero. Also, as the 1.3V threshold is exceeded, the
Soft-start capacitor charging current decreases from 5 μA
down to approximately 1.6 μA. This decreases the slope of
capacitor voltage ramp.
3. Soft-start Region.
When the SD /SS pin voltage is be-
tween 1.8V and 2.8V (
@
25C), the regulator is in a Soft-start
condition. The switch (Pin 2) duty cycle initially starts out
very low, with narrow pulses and gradually get wider as the
capacitor SD /SS pin ramps up towards 2.8V. As the duty
cycle increases, the output voltage also increases at a con-
trolled ramp up. See the center curve in Figure 13 The input
supply current requirement also starts out at a low level for
DS012582-30
FIGURE 12.
L
www.national.com
18
相關PDF資料 |
PDF描述 |
|---|---|
| LM2599T-12 | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| LM2599T-3.3 | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| LM2599T-5.0 | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| LM2599T-ADJ | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| LM2619MTC | 500mA Step-Down DC-DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2599SADJ | 制造商:National Semiconductor 功能描述:Conv DC-DC Single Step Down 4.5V to 40V 8-Pin(7+Tab) TO-263 T/R |
| LM2599S-ADJ | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2599S-ADJ/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2599SX-12 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2599SX-12/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。