- 您現在的位置：買賣IC網 > PDF目錄361024 > LM2599T-ADJ (NATIONAL SEMICONDUCTOR CORP) SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features PDF資料下載
參數資料
| 型號： | LM2599T-ADJ |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| 中文描述： | 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, PZFM7 |
| 封裝： | TO-220, 7 PIN |
| 文件頁數： | 10/31頁 |
| 文件大小： | 812K |
| 代理商： | LM2599T-ADJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
LM2599 Series Buck Regulator Design Procedure (Fixed Output)
PROCEDURE (Fixed Output Voltage Version)
EXAMPLE (Fixed Output Voltage Version)
Given:
V
OUT
= Regulated Output Voltage (3.3V, 5V or 12V)
V
IN
(max) = Maximum DC Input Voltage
I
LOAD
(max) = Maximum Load Current
Given:
V
OUT
= 5V
V
IN
(max) = 12V
I
LOAD
(max) = 3A
1. Inductor Selection (L1)
A.
Select the correct inductor value selection guide from Fig-
ure 4 Figure 5 or 6. (Output voltages of 3.3V, 5V, or 12V re-
spectively.) For all other voltages, see the design procedure
for the adjustable version.
B.
From the inductor value selection guide, identify the induc-
tance region intersected by the Maximum Input Voltage line
and the Maximum Load Current line. Each region is identified
by an inductance value and an inductor code (LXX).
C.
Select an appropriate inductor from the four manufactur-
er’s part numbers listed in Figure 8
1. Inductor Selection (L1)
A.
Use the inductor selection guide for the 5V version shown
in Figure 5
B.
From the inductor value selection guide shown in Figure 5
the inductance region intersected by the 12V horizontal line
and the 3A vertical line is 33 μH, and the inductor code is
L40.
C.
The inductance value required is 33 μH. From the table in
Figure 8 go to the L40 line and choose an inductor part num-
ber from any of the four manufacturers shown. (In most in-
stance, both through hole and surface mount inductors are
available.)
2. Output Capacitor Selection (C
OUT
)
A.
In the majority of applications, low ESR (Equivalent Series
Resistance) electrolytic capacitors between 82 μF and 820
μF and low ESR solid tantalum capacitors between 10 μF
and 470 μF provide the best results. This capacitor should be
located close to the IC using short capacitor leads and short
copper traces. Do not use capacitors larger than 820 μF.
For additional information, see section on output capaci-
tors in application information section.
B.
To simplify the capacitor selection procedure, refer to the
quick design component selection table shown in Figure 2
This table contains different input voltages, output voltages,
and load currents, and lists various inductors and output ca-
pacitors that will provide the best design solutions.
C.
The capacitor voltage rating for electrolytic capacitors
should be at least 1.5 times greater than the output voltage,
and often much higher voltage ratings are needed to satisfy
the low ESR requirements for low output ripple voltage.
D.
For computer aided design software, see
Switchers
Made Simple
(version 4.2.1 or later).
2. Output Capacitor Selection (C
OUT
)
A. See section on output capacitors in application infor-
mation section.
B.
From the quick design component selection table shown
in Figure 2 locate the 5V output voltage section. In the load
current column, choose the load current line that is closest to
the current needed in your application, for this example, use
the 3A line. In the maximum input voltage column, select the
line that covers the input voltage needed in your application,
in this example, use the 15V line. Continuing on this line are
recommended inductors and capacitors that will provide the
best overall performance.
The capacitor list contains both through hole electrolytic and
surface mount tantalum capacitors from four different capaci-
tor manufacturers. It is recommended that both the manufac-
turers and the manufacturer’s series that are listed in the
table be used.
In this example aluminum electrolytic capacitors from several
different manufacturers are available with the range of ESR
numbers needed.
330 μF
35V
Panasonic HFQ Series
330 μF
35V
Nichicon PL Series
C.
For a 5V output, a capacitor voltage rating at least 7.5V or
more is needed. But even a low ESR, switching grade, 220
μF 10V aluminum electrolytic capacitor would exhibit ap-
proximately 225 m
of ESR (see the curve in Figure 16 for
the ESR vs voltage rating). This amount of ESR would result
in relatively high output ripple voltage. To reduce the ripple to
1% of the output voltage, or less, a capacitor with a higher
value or with a higher voltage rating (lower ESR) should be
selected. A 16V or 25V capacitor will reduce the ripple volt-
age by approximately half.
L
www.national.com
10
相關PDF資料 |
PDF描述 |
|---|---|
| LM2619MTC | 500mA Step-Down DC-DC Converter |
| LM2619MTCX | 500mA Step-Down DC-DC Converter |
| LM2621MM | Low Input Voltage, Step-Up DC-DC Converter |
| LM2621 | |
| LM2622 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2599T-ADJ | 制造商:Texas Instruments 功能描述:SWITCHING REG 3A ADJ 2599 TO2207 |
| LM2599T-ADJ/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM26 | 制造商:Psiber Data Systems 功能描述:LanMaster 26 Pro Link Tester and Accesory Kit |
| LM26_07 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:SOT-23, ±3°C Accurate, Factory Preset Thermostat |
| LM26001 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.5A Switching Regulator with High Efficiency Sleep Mode |
發布緊急采購，3分鐘左右您將得到回復。