- 您現在的位置：買賣IC網 > PDF目錄361025 > LM2984 (National Semiconductor Corporation) Microprocessor Power Supply System PDF資料下載
參數資料
| 型號： | LM2984 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Microprocessor Power Supply System |
| 中文描述： | 微機電源系統 |
| 文件頁數： | 5/16頁 |
| 文件大小： | 398K |
| 代理商： | LM2984 |
Electrical Characteristics
(Continued)
V
= 14V, I
= 5 mA, I
= 5 mA, I
= 5 mA, R
= 130 k
, C
= 0.33 μF, C
mon
= 0.47 μF, unless otherwise indicated,
Boldface
type refers to limits over the entire operating temperature range, 40C
T
A
≤
+125C, all other limits are for T
A
= T
J
= 25C (Note 8)
Parameter
Conditions
Typical
Limit
(Note 4)
Units
Computer Monitor/Reset Functions
Reset Rise Time
On/Off Switch Input
Current (Pin 8)
On/Off Switch Input
Threshold Voltage
R
rst
= 10k, V
rst
= 5V, C
rst
≤
10 pF
V
ON
= 2.4V
V
ON
= 0.4V
0.60
7.5
0.01
1.22
1.22
1.00/
1.50
25/
25
10/
10
0.80/
0.80
2.00/
2.00
μs
max
μA
max
μA
max
V
min
V
max
Note 2:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its specified operating ratings.
Note 3:
Thermal resistance without a heatsink for junction-to-case temperature is 3C/W. Thermal resistance case-to-ambient is 40C/W.
Note 4:
Tested Limits are guaranteed and 100% production tested.
Note 5:
Human body model, 100 pF capacitor discharged through a 1500
resistor.
Note 6:
Internal comparators detect when the main regulator output (V
) changes from the measured output voltage (with V
= 14V) by the specified amount,
V
High or
V
Low, and set the Reset Error Flag low. The Reset Error Flag is held low until V
OUT
returns to regulation. The Reset Error Flag is then allowed
to go high again after a delay set by R
t
and C
t
. (see application section).
Note 7:
This parameter is a measure of how short a pulse can be detected at the μP Monitor Input. This parameter is primarily influenced by the value of C
mon
. (See
Application Hints Section.)
Note 8:
To ensure constant junction temperature, low duty cycle pulse testing is used.
Block Diagram
DS011252-2
5
www.national.com
相關PDF資料 |
PDF描述 |
|---|---|
| LM302 | LM102/LM302 Voltage Followers |
| LM102 | Voltage Followers |
| LM3075 | High Efficiency, Synchronous Current Mode Buck Controller |
| LM3075MTC | High Efficiency, Synchronous Current Mode Buck Controller |
| LM3075MTCX | High Efficiency, Synchronous Current Mode Buck Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2984CT | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM2984CT/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM2984T | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM2984T/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM2990J-12-QML | 制造商:National Semiconductor Corporation 功能描述:LDO Regulator Neg -12V 1.8A 16-Pin CDIP Tray 制造商:National Semiconductor 功能描述:LDO Regulator Neg -12V 1.8A 16-Pin CDIP Tray |
發布緊急采購，3分鐘左右您將得到回復。