- 您現在的位置：買賣IC網 > PDF目錄361029 > LM4865 (National Semiconductor Corporation) 750 mW Audio Power Amplifier with DC Volume Control and Headphone Switch PDF資料下載
參數資料
| 型號： | LM4865 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 750 mW Audio Power Amplifier with DC Volume Control and Headphone Switch |
| 中文描述： | 750毫瓦音頻功率放大器直流音量控制和耳機開關 |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 340K |
| 代理商： | LM4865 |
Typical Performance Characteristics
(Continued)
Application Information
BRIDGE CONFIGURATION EXPLANATION
As shown in Figure 1 , the LM4865 has two operational am-
plifiers internally, allowing for a few different amplifier con-
figurations. The first amplifier’s gain is DC voltage controlled,
while the second amplifier is internally fixed in a unity-gain,
inverting configuration. The closed-loop gain of the first am-
plifier is set by an external DC voltage (refer to (Figure 1),
while the second amplifier’s gain is fixed by the two internal
20 k
resistors.
Figure 1shows that the output of amplifier one serves as the
input to amplifier two which results in both amplifiers produc-
ing signals identical in magnitude, but out of phase 180.
By driving the load differentially through outputs V
and
V
, an amplifier configuration commonly referred to as
“bridged mode” is established. Bridged mode operation is
different from the classical single-ended amplifier configura-
tion where one side of its load is connected to ground.
A bridge amplifier design has a few distinct advantages over
the single-ended configuration, as it provides differential
drive to the load, thus doubling output swing for a specified
supply voltage. Four times the output power is possible as
compared to a single-ended amplifier under the same condi-
tions. This increase in attainable output assumes that the
amplifier is not current limited or clipped. In order to choose
an amplifier’s closed-loop gain without causing excessive
clipping, please refer to the
Audio Power Amplifier Design
section.
THD+N vs Output Power
DS101025-23
THD+N vs Output Power
DS101025-24
THD+N vs Output Power
DS101025-28
Output Power vs Load Resistance
DS101025-29
Clipping Voltage vs Supply Voltage
DS101025-30
Output Power vs Supply Voltage
DS101025-31
Output Power vs Supply Voltage
DS101025-32
Supply Current vs Supply Voltage
DS101025-33
L
www.national.com
5
相關PDF資料 |
PDF描述 |
|---|---|
| LM4865M | 750 mW Audio Power Amplifier with DC Volume Control and Headphone Switch |
| LM4865MM | 750 mW Audio Power Amplifier with DC Volume Control and Headphone Switch |
| LM4866 | 2.2W Stereo Audio Amplifier |
| LM4866LQ | 2.2W Stereo Audio Amplifier |
| LM4866MT | 2.2W Stereo Audio Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4865IBP | 制造商:Texas Instruments 功能描述: |
| LM4865IBP/NOPB | 功能描述:IC AMP AUDIO PWR 1W MONO 8USMD RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4865IBPX | 功能描述:IC AMP AUDIO PWR 1W MONO 8USMD RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4865M | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4865M | 制造商:Texas Instruments 功能描述:AMP AUDIO/VOLT CONTROL 0.75W 4865 |
發布緊急采購，3分鐘左右您將得到回復。