- 您現在的位置：買賣IC網 > PDF目錄361029 > LM4866MTE (NATIONAL SEMICONDUCTOR CORP) 2.2W Stereo Audio Amplifier PDF資料下載
參數資料
| 型號： | LM4866MTE |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 2.2W Stereo Audio Amplifier |
| 中文描述： | 3.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| 封裝： | 6.50 X 4.40 MM, 0.90 MM HEIGHT, EXPOSED PAD, TSSOP-20 |
| 文件頁數： | 11/21頁 |
| 文件大小： | 644K |
| 代理商： | LM4866MTE |
Application Information
(Continued)
BRIDGE CONFIGURATION EXPLANATION
As shown in
Figure 1
, the LM4866 consists of two pairs of
operational amplifiers, forming a two-channel (channelAand
channel B) stereo amplifier. (Though the following discusses
channel A, it applies equally to channel B.) External resistors
R
f
and R
i
set the closed-loop gain of Amp1A, whereas two
internal 20k
resistors set Amp2A’s gain at -1. The LM4866
drives a load, such as a speaker, connected between the two
amplifier outputs, -OUTA and +OUTA.
Figure 1
shows that Amp1A’s output serves as Amp2A’s
input. This results in both amplifiers producing signals iden-
tical in magnitude, but 180 out of phase. Taking advantage
of this phase difference, a load is placed between -OUTA
and +OUTA and driven differentially (commonly referred to
as ’bridge mode’). This results in a differential gain of
A
VD
= 2 x (R
f
/ R
i
)
(1)
Bridge mode amplifiers are different from single-ended am-
plifiers that drive loads connected between a single amplifi-
er’s output and ground. For a given supply voltage, bridge
mode has a distinct advantage over the single-ended con-
figuration: its differential output doubles the voltage swing
across the load. This produces four times the output power
when compared to a single-ended amplifier under the same
conditions. This increase in attainable output power as-
sumes that the amplifier is not current limited or that the
output signal is not clipped. To ensure minimum output sig-
nal clipping when choosing an amplifier’s closed-loop gain,
refer to the
Audio Power Amplifier Design
section.
Another advantage of the differential bridge output is no net
DC voltage across the load. This is accomplished by biasing
channel A’s and channel B’s outputs at half-supply. This
eliminates
the
coupling
capacitor
single-ended amplifiers require. Eliminating an output cou-
pling capacitor in a single-ended configuration forces a
single-supply amplifier’s half-supply bias voltage across the
load. This increases internal IC power dissipation and may
permanently damage loads such as speakers.
that
single
supply,
POWER DISSIPATION
Power dissipation is a major concern when designing a
successful single-ended or bridged amplifier. Equation (2)
states the maximum power dissipation point for a single-
ended amplifier operating at a given supply voltage and
driving a specified output load
P
DMAX
= (V
DD
)
2
/ (2
π
2
R
L
) Single-Ended
(2)
However, a direct consequence of the increased power de-
livered to the load by a bridge amplifier is higher internal
power dissipation for the same conditions.
The LM4866 has two operational amplifiers per channel. The
maximum internal power dissipation per channel operating in
the bridge mode is four times that of a single-ended ampli-
20018601
*
Refer to the section Proper Selection of External Components, for a detailed discussion of C
B
size.
FIGURE 1. Typical Audio Amplifier Application Circuit
Pin out shown for the LLP package. Refer to the Connection Diagrams for the pinout of the TSSOP package.
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM4867 | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| LM4867LQ | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| LM4867MT | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| LM4867MTE | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| LM4868 | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4866MTE/NOPB | 功能描述:音頻放大器 2.2W Stereo Audio Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4866MTEX | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4866MTEX/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4866MTEXNOPB | 制造商:National Semiconductor 功能描述:Audio Amp Speaker 2-CH Stereo 3.2W Class-AB 20-Pin HTSSOP EP T/R 制造商:National Semiconductor 功能描述:Audio Amp Speaker 2-CH Stereo 3.2W Class-AB 20-Pin TSSOP EP T/R |
| LM4867 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Output-Transient-Free Dual 2.1W Audop Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
發布緊急采購，3分鐘左右您將得到回復。