- 您現在的位置：買賣IC網 > PDF目錄361029 > LM4867MT (NATIONAL SEMICONDUCTOR CORP) Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function PDF資料下載
參數資料
| 型號： | LM4867MT |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| 中文描述： | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| 封裝： | 4.40 MM, TSSOP-20 |
| 文件頁數： | 13/26頁 |
| 文件大小： | 763K |
| 代理商： | LM4867MT |
Application Information
(Continued)
the bridge mode is four times that of a single-ended ampli-
fier. From Equation (3), assuming a 5V power supply and an
4
load, the maximum single channel power dissipation is
1.27W or 2.54W for stereo operation.
P
DMAX
= 4
*
(V
DD
)
2
/(2
π
2
R
L
):
Bridge Mode
(3)
The LM4867’s power dissipation is twice that given by Equa-
tion (2) or Equation (3) when operating in the single-ended
mode or bridge mode, respectively. Twice the maximum
power dissipation point given by Equation (3) must not ex-
ceed the power dissipation given by Equation (4):
P
DMAX
’ = (T
JMAX
T
A
)/
θ
JA
(4)
The LM4867’s TJMAX = 150C. In the LQ package soldered
to a DAP pad that expands to a copper area of 5in
2
on a
PCB, the LM4867’s
θ
JA
is 20C/W. In the MTE package
soldered to a DAP pad that expands to a copper area of 2in
2
on a PCB, the LM4867’s
θ
JA
is 41C/W.At any given ambient
temperature T
A
, use Equation (4) to find the maximum inter-
nal power dissipation supported by the IC packaging. Rear-
ranging Equation (4) and substituting P
for P
’ re-
sults in Equation (5). This equation gives the maximum
ambient temperature that still allows maximum stereo power
dissipation without violating the LM4867’s maximum junction
temperature.
T
A
= T
JMAX
2 X P
DMAX
θ
JA
(5)
For a typical application with a 5V power supply and an 4
load, the maximum ambient temperature that allows maxi-
mum stereo power dissipation without exceeding the maxi-
mum junction temperature is approximately 99C for the LQ
package and 45C for the MTE package.
T
JMAX
= P
DMAX
θ
JA
+ T
A
(6)
Equation (6) gives the maximum junction temperature
T
. If the result violates the LM4867’s 150C, reduce the
maximum junction temperature by reducing the power sup-
ply voltage or increasing the load resistance. Further allow-
ance should be made for increased ambient temperatures.
The above examples assume that a device is a surface
mount part operating around the maximum power dissipation
point. Since internal power dissipation is a function of output
power, higher ambient temperatures are allowed as output
power or duty cycle decreases.
If the result of Equation (2) is greater than that of Equation
(3), then decrease the supply voltage, increase the load
impedance, or reduce the ambient temperature. If these
measures are insufficient, a heat sink can be added to
reduce
θ
. The heat sink can be created using additional
copper area around the package, with connections to the
ground pin(s), supply pin and amplifier output pins. External,
solder attached SMT heatsinks such as the Thermalloy
7106D can also improve power dissipation. When adding a
heat sink, the
θ
JA
is the sum of
θ
JC
,
θ
CS
, and
θ
SA
. (
θ
JC
is the
junctiontocase
casetosink
sinktoambient thermal impedance.) Refer to the
Typical
Performance Characteristics
curves for power dissipation
information at lower output power levels.
thermal
impedance,
impedance,
θ
CS
θ
SA
is
is
the
the
thermal
and
POWER SUPPLY BYPASSING
As with any power amplifier, proper supply bypassing is
critical for low noise performance and high power supply
rejection. Applications that employ a 5V regulator typically
use a 10μF in parallel with a 0.1μF filter capacitors to stabi-
lize the regulator’s output, reduce noise on the supply line,
and improve the supply’s transient response. However, their
presence does not eliminate the need for a local 1.0μF
tantalum bypass capacitance connected between the
LM4867’s supply pins and ground. Do not substitute a ce-
ramic capacitor for the tantalum. Doing so may cause oscil-
lation. Keep the length of leads and traces that connect
capacitors between the LM4867’s power supply pin and
ground as short as possible. Connecting a 1μF capacitor,
C
, between the BYPASS pin and ground improves the
internal bias voltage’s stability and improves the amplifier’s
PSRR. The PSRR improvements increase as the bypass pin
capacitor value increases. Too large, however, increases
turnon time and can compromise the amplifier’s click and
pop performance. The selection of bypass capacitor values,
especially C
, depends on desired PSRR requirements,
click and pop performance (as explained in the section,
Proper Selection of External Components
), system cost,
and size constraints.
MICROPOWER SHUTDOWN
The voltage applied to the SHUTDOWN pin controls the
LM4867’s shutdown function. Activate micropower shut-
down by applying V
to the SHUTDOWN pin. When active,
the LM4867’s micropower shutdown feature turns off the
amplifier’s bias circuitry, reducing the supply current. The
logic threshold is typically V
/2. The low 0.7μA typical
shutdown current is achieved by applying a voltage that is as
near as V
as possible to the SHUTDOWN pin. A voltage
that is less than V
may increase the shutdown current.
Table 1 shows the logic signal levels that activate and deac-
tivate micropower shutdown and headphone amplifier op-
eration.
To ensure that the output signal remains
transientfree, do not cycle the shutdown function
faster than 1Hz.
There are a few ways to control the micropower shutdown.
These include using a singlepole, single, throw switch, a
microprocessor, or a microcontroller. When using a switch,
connect an external 100k
pullup resistor between the
SHUTDOWN pin and V
. Connect the switch between the
SHUTDOWN pin and ground. Select normal amplifier opera-
tion by closing the switch. Opening the switch connects the
SHUTDOWN pin to V
through the pullup resistor, acti-
vating micropower shutdown. The switch and resistor guar-
antee that the SHUTDOWN pin will not float. This prevents
unwanted state changes. In a system with a microprocessor
or a microcontroller, use a digital output to apply the control
voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin
with active circuitry eliminates the pull up resistor.
L
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM4867MTE | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| LM4868 | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| LM4868MTE | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| LM4868LQ | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
| LM4868MT | Output-Transient-Free Dual 2.1W Audio Amplifier Plus No Coupling Capacitor Stereo Headphone Function |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4867MT NOPB | 制造商:Texas Instruments 功能描述:Audio Amp Headphone/Speaker 2-CH Stereo 1.5W Class-AB 20-Pin TSSOP Rail |
| LM4867MT/NOPB | 功能描述:IC AMP AUDIO PWR 3W AB 20TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4867MTE | 制造商:Texas Instruments 功能描述:Audio Amp Headphone/Speaker 2-CH Stereo 3W Class-AB 20-Pin TSSOP EP Rail |
| LM4867MTE/NOPB | 功能描述:IC AMP AUDIO PWR 3W AB 20TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4867MTEX | 制造商:National Semiconductor Corporation 功能描述:Audio Amplifier Circuit, Dual, 20 Pin, Plastic, TSSOP |
發布緊急采購，3分鐘左右您將得到回復。