- 您現在的位置：買賣IC網 > PDF目錄361030 > LM5026SDX (NATIONAL SEMICONDUCTOR CORP) Active Clamp Current Mode PWM Controller PDF資料下載
參數資料
| 型號： | LM5026SDX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Active Clamp Current Mode PWM Controller |
| 中文描述： | 3 A SWITCHING CONTROLLER, 660 kHz SWITCHING FREQ-MAX, DSO16 |
| 封裝： | 5 X 5 MM, EXPOSED PAD, LLP-16 |
| 文件頁數： | 16/23頁 |
| 文件大小： | 936K |
| 代理商： | LM5026SDX |
Oscillator and Sync Capability
(Continued)
Multiple LM5026 devices can be synchronized together sim-
ply by connecting the devices SYNC pins together as shown
in
Figure 9
. Care should be taken to ensure the ground
potential differences between devices are minimized. In this
configuration all of the devices will be synchronized to the
highest frequency device. The internal block diagram of the
oscillator and synchronization circuit is shown in
Figure 10
.
The SYNC I/O pin is a CMOS buffer with pull-up current
limited to 200 μA. If an external device forces the SYNC pin
low before the internal oscillator ramp completes its charging
cycle, the ramp will be reset and another cycle begins. If the
SYNC pins of multiple LM5026 devices are connected to-
gether, the first SYNC pin that pulls low will reset the oscil-
lator RAMP of all other devices. All controllers will operate in
phase when synchronized using the SYNC I/O feature. Up to
five LM5026 devices can be synchronized using this tech-
nique.
Thermal Protection
Internal Thermal Shutdown circuitry is provided to protect the
integrated circuit in the event the maximum junction tem-
perature is exceeded. When activated, typically at 165C,
the controller is forced into a low power standby state with
the output drivers and the bias regulator disabled. The de-
vice will restart after the thermal hysteresis (typically 25C).
During thermal shutdown, the soft-start capacitor is fully
discharged and the controller follows a normal start-up se-
quence after the junction temperature falls to the operating
level.
Applications Information
LINE INPUT (VIN)
The LM5026 contains an internal high voltage start-up regu-
lator that allows the input pin (VIN) to be connected directly
to a nominal 48V line voltage. The voltage applied to the VIN
pin can vary in the range of 13 to 100V with transient
capability to 105V. When power is applied and the UVLO pin
potential is greater than 0.4V, the VCC regulator is enabled
and sources current into an external capacitor connected to
the VCC pin. When the voltage on the VCC pin reaches the
regulation point of 7.7V, the internal voltage reference (REF)
is enabled. The reference regulation set point is 5V. The
controller outputs are enabled when the UVLO pin potential
is greater than 1.25V. In typical applications, an auxiliary
transformer winding is connected through a diode to the
VCC pin. This winding must raise the VCC voltage above 8V
to shut off the internal start-up regulator. It is recommended
a filtering circuit shown in
Figure 11
be used to suppress
transients, which may occur at the input supply, in particular
when VIN is operated close to the maximum operating rat-
ing.
FOR APPLICATION
>
100V
For applications where the system input voltage exceed
100V or IC power dissipation is a concern, the LM5026 can
be powered from an external start-up regulator as shown in
Figure 12
. In this configuration, the VIN and the VCC pins
should be connected together, which allows the LM5026 to
be operated below 13V. The voltage at the VCC pin must be
greater than 8V yet not exceed 15V.An auxiliary winding can
be used to reduce the dissipation in the external regulator
once the power converter is active.
20147920
FIGURE 9. Sync from Multiple Devices
20147921
FIGURE 10. Oscillator Sync I/O Block Diagram
20147922
FIGURE 11. Input Transient Protection
L
www.national.com
16
相關PDF資料 |
PDF描述 |
|---|---|
| LM5030 | 100V Push-Pull Current Mode PWM Controller |
| LM5030MM | 100V Push-Pull Current Mode PWM Controller |
| LM5030MMX | 100V Push-Pull Current Mode PWM Controller |
| LM556 | Dual Timer |
| LM556ICN | Analog Timer Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5026SDX/NOPB | 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| LM5027 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Voltage Mode Active Clamp Controller |
| LM5027A | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Evaluation Board evaluation board is designed to provide |
| LM5027A-EVAL/NOPB | 功能描述:電源管理IC開發工具 LM5027A EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM5027AMH/NOPB | 功能描述:電壓模式 PWM 控制器 Active Clamp Pwm W/3A Sr Drv RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。