欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: LM8300IMT9
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 消費家電
英文描述: Four Wire Resistive Touchscreen Controller with Brownout
中文描述: SPECIALTY CONSUMER CIRCUIT, PDSO48
封裝: TSSOP-48
文件頁數: 18/20頁
文件大小: 327K
代理商: LM8300IMT9
14.0 Calibration
(Continued)
send a reply byte of $CC to the TS driver. At this point, the
TS driver should either notify the user to redo the calibration
point or automatically redo the calibration again. If the self-
test was successful, the device will send a reply byte of $CB
to the TS driver.
14.3 CALIBRATION PROCEDURES WITH
COORDINATES CHECKING DISABLED
To do TS calibration with coordinates checking disabled, first
ensure the Calibration Coordinates Checking is disabled on
the device. This can be accomplished by sending a com-
mand byte of $B1 (Read Parameters command) and check-
ing the 5th bit of the 12th reply byte is not set. Alternatively,
if the device is set to Calibration Coordinates Checking
disabled as default, this step can be skipped.
The TS driver sends the command byte to do calibration
($BD). The TS driver should wait for the reply bytes and
15.0 Revision History
ensure it is the same command bytes it sent. The device
waits for a touch to be detected on the panel. Once a touch
is detected, the device save the values into the internal flash
and send a reply byte of $C4 to the TS driver. The TS driver
can now send a command byte to do the next calibration
point. Since the Calibration Checking is disabled, the TS
driver should ensure the calibration point is within the range
of the calibration cross.
Once all the calibration points are done, the device does a
self-test. If the self-test was not successful, the device will
send a reply byte of $CC to the TS driver. At this point, the
TS driver should either notify the user to redo the calibration
point or automatically redo the calibration again. If the self-
test was successful, the device will send a reply byte of $CB
to the TS driver.
Date
Section
Summary of Changes
October 2002
May 2003
Initial release.
Removed LM8400 part.
Updated section to reflect the change and made external reset circuitry
optional.
Added command byte $A5
Updated controller reply bytes
Added description for command byte $A5
All sections
Brownout Reset
July 2003
Advanced Command Bytes
Descriptions
December
2003
Advanced Command Bytes
Descriptions
L
www.national.com
18
相關PDF資料
PDF描述
LM8300IVA9 Four Wire Resistive Touchscreen Controller with Brownout
LM8300 Four Wire Resistive Touchscreen Controller with Brownout
LM8300HLQ9 Four Wire Resistive Touchscreen Controller with Brownout
LM8300HMT9 Four Wire Resistive Touchscreen Controller with Brownout
LM831 LM831 Low Voltage Audio Power Amplifier
相關代理商/技術參數
參數描述
LM8300IMT9/NOPB 制造商:Texas Instruments 功能描述:Four Wire Resistive Touchscreen Controller With Brownout 48-Pin TSSOP
LM8300IMT9B 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
LM8300IMT9B/63 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
LM8300IMT9B/63SN 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
LM8300IMT9B/NOPB 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20
主站蜘蛛池模板: 扶风县| 宣化县| 蓬莱市| 河北省| 精河县| 奇台县| 纳雍县| 宝鸡市| 柳州市| 交城县| 万山特区| 台山市| 调兵山市| 宜川县| 泉州市| 兰州市| 长春市| 罗田县| 遵义市| 东丽区| 昌邑市| 广丰县| 松滋市| 高州市| 大新县| 桑植县| 池州市| 图们市| 平泉县| 兴隆县| 阿图什市| 禄丰县| 清新县| 衢州市| 鄂尔多斯市| 彩票| 华容县| 抚宁县| 清丰县| 屯门区| 临颍县|