- 您現在的位置：買賣IC網 > PDF目錄361035 > LM84 (National Semiconductor Corporation) Diode Input Digital Temperature Sensor with Two-Wire Interface PDF資料下載
參數資料
| 型號： | LM84 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Diode Input Digital Temperature Sensor with Two-Wire Interface |
| 中文描述： | 二極管輸入數字溫度傳感器兩線接口 |
| 文件頁數： | 9/16頁 |
| 文件大小： | 168K |
| 代理商： | LM84 |
Logic Electrical Characteristics
(Continued)
1.0 Functional Description
The LM84 temperature sensor incorporates a band-gap type
temperature sensor using a Local or Remote diode and an
8-bit ADC (Delta-Sigma Analog-to-Digital Converter). The
LM84 is compatible with the serial SMBus and I
2
C inter-
faces. Digital comparators compare Local and Remote read-
ings
to
user-programmable
RT_CRIT). Activation of the T_CRIT_A output indicates that
a temperature reading is greater than the limit preset in a
T_CRIT register.
setpoints
(LT_CRIT
and
1.1 T_CRIT_A OUTPUT, T_CRIT LIMITS
T_CRIT_A is activated when the Local temperature reading
is greater than the limit preset in the local critical temperature
setpoint register (LT_CRIT) or when the Remote tempera-
ture reading is greater than the limit preset in the remote
critical temperature setpoint register (RT_CRIT), as shown in
Figure 3 The T_CRIT_A mask bit (bit 7 of the Configuration
Register) when set will disable the T_CRIT_A output.
The Status Register can be read to determine which event
caused the alarm. A bit in the Status Register is set high to
indicate T_CRIT temperature alarm, see Section 1.8.3
Local and remote temperature diodes are sampled alter-
nately by the A/D converter. The T_CRIT_A output and the
Status Register flags are updated at the completion of a
conversion, which takes approximately 60 ms. T_CRIT_A
and the Status Register flags are reset only after the Status
Register is read and if the temperature is below the setpoint.
1.2 POWER-ON RESET DEFAULT STATES
LM84 always powers up to these known default states:
1.
Local Temperature set to 0C
2.
Remote Temperature set to 0C until the LM84 senses a
diode present or open circuit on the D+ and D input
pins.
3.
Status Register set to 00h.
4.
Command Register set to 00h; T_CRIT_A enabled.
5.
Local and Remote T_CRIT set to 127C
DS100961-5
FIGURE 2. Temperature-to-Digital Transfer Function (Non-linear scale for clarity)
DS100961-6
FIGURE 3. T_CRIT_A Temperature Response Diagram
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM84CIMQA | Diode Input Digital Temperature Sensor with Two-Wire Interface |
| LM9011 | Electronic Ignition Interface |
| LM9011M | Multipole Connector; Gender:Male; Number of Contacts:9; Series:1625P; Body Material:PA Polyamide (Nylon) 6/6; Connecting Termination:Crimp; Number of Rows:3; Operating Voltage:250V; Pitch Spacing:1.57mm |
| LM9022 | Vacuum Fluorescent Display Filament Driver |
| LM9022M | Vacuum Fluorescent Display Filament Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8400 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8460 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:ALARM CLOCK (CLOCK RADIO.ETC) |
| LM8471 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LM84B WAF | 制造商:Texas Instruments 功能描述: |
| LM84BIMQA | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。