- 您現在的位置：買賣IC網 > PDF目錄361035 > LM9831CCVJD (NATIONAL SEMICONDUCTOR CORP) LM9831 42-Bit Color, 1200dpi USB Image Scanner PDF資料下載
參數資料
| 型號： | LM9831CCVJD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | LM9831 42-Bit Color, 1200dpi USB Image Scanner |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封裝： | PLASTIC, TQFP-100 |
| 文件頁數： | 27/41頁 |
| 文件大小： | 320K |
| 代理商： | LM9831CCVJD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
27
www.national.com
Off value and the lamp will always stay on. Illumination Mode 2
timing is shown in Figure 21, and in slightly more detail in Figure
33.
Illumination Mode 3 is similar to Illumination Mode 2, except that
the LAMP outputs for all three colors are turned on and off every
line. Illumination Mode 3 timing is shown in Figures 22 and 23.
The Lamp On and Lamp Off settings work the same as in Mode 2
to control the on and off points for the different lamp signals. In
systems with a limited power budget, care should be taken to pre-
vent turning multiple lamps on at the same time. This can also be
important for CIS sensors that limit the maximum combined cur-
rent of the three lamps.
These modes are in operation whenever the chip is powered on
and not in standby mode. For example, the LAMP outputs in Fig-
ures 21 and 22 keep pulsing whether the LM9831 is in the Idle,
Paper Feed, or Scanning states. This eliminates light amplitude
variations due to the lamp/LEDs warm-up characteristics. Since
the LAMP pulses are synchronized to the TR pulse, which is
determined by the horizontal pixel counter, this means that the
pixel counter is constantly running, and any new scans can only
be started by waiting for the next new line (the next Red line in
the case of Illumination Mode 2).
5.2 CCD/CIS Control Block
This function generates the clock signals necessary to control a
CCD or CIS sensor. Refer to the descriptions for registers 0B to
18 for more details on the timing of specific signals. The LM9831
features:
Independent control over the polarity (inverting or noninverting)
of the input stage to accommodate CIS or CDS signals.
Full timing control of the CIS and CDS sample points. Refer-
ence and signal sample points can be independently adjusted.
Note that the absolute time between reference sample and sig-
nal sample must be 2 MCLKs or greater, whether CDS is on or
off.
Ability to turn off CDS. When CDS is on, traditional CDS is per-
formed. When CDS is off, the signal is sampled at the Sample
Signal point, but the internal reference is used for the Sample
Reference voltage (not a point on the input signal itself).
The CP1 output supplies the CP pulse needed on some popu-
lar Toshiba CCDs. This looks and acts just like another, inde-
pendent RS pulse.
A CP2 output is another independent pixel rate pulse that (if
needed) can be programmed to supply an additional clock.
CCD clock signals RS, CP1, CP2 are reset when Line Ends
The internal Clamp signal is reset with Optical Black Pixels
End.
TR1 and TR2 pulse widths are always the same width, as
determined by Register 0E.
The TR-1 guardband may be equal to 0, causing TR and 1
to go high simultaneously and low simultaneously (Figure 24).
This is a requirement of some Canon CIS sensors.
CIS TR1 Timing Mode 1. In this mode the TR1 pulse is exactly
one clock long, occurring on the rising edge of 1. The TR1
pulse width and guardband settings are ignored. For Dyna CIS.
CIS TR1 Timing Mode 2. In this mode the TR pulse is again
equal to 1 period, but now it is centered around 1. The TR
pulse width and guardband settings are ignored. For Canon
CIS.
To prevent sensor saturation, the LM9831 is always clocking
Figure 21:
Illumination Mode 2
TR
LAMP
G
LAMP
B
LAMP
R
Figure 22:
Illumination Mode 3 (grayscale)
TR
LAMP
G
LAMP
B
LAMP
R
Figure 23:
Illumination Mode 3 (green only)
TR
LAMP
G
LAMP
R
(LAMP
R
On > Line End, LAMP
R
Off < Line End
LAMP
B
(LAMP
B
On > Line End, LAMP
B
Off < Line End
TR Pulse same as first clock pulse
Figure 24:
TR-1Guardband Can Be Equal To 0
TR
1
Figure 25:
CIS TR1 Timing Mode 1
Dummy
Pixels
RS
TR1
1
Transfer
Phase
Previous
Line
1 inside TR1 pulse
Figure 26:
CIS TR1 Timing Mode 2
TR1
1
t
1
/4
t
1
/4
t
1
/4
t
1
相關PDF資料 |
PDF描述 |
|---|---|
| LM9831 | LM9831 42-Bit Color, 1200dpi USB Image Scanner |
| LM9831CCVJDX | LM9831 42-Bit Color, 1200dpi USB Image Scanner |
| LM9832CCVJD | LM9832 42-Bit Color, 1200dpi USB Image Scanner |
| LM9832 | LM9832 42-Bit Color, 1200dpi USB Image Scanner |
| LM9833CCVJD | LM9833 48-Bit Color, 1200dpi USB Image Scanner |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9831CCVJDX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9831 42-Bit Color, 1200dpi USB Image Scanner |
| LM9832 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9832 42-Bit Color, 1200dpi USB Image Scanner |
| LM9832B-B WAF | 制造商:Texas Instruments 功能描述: |
| LM9832B-E WAF | 制造商:Texas Instruments 功能描述: |
| LM9832CCVJD | 功能描述:IC SCANNER CLR USB IMAGE 100TQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模擬前端 (AFE) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:- 通道數:2 功率（瓦特）:- 電壓 - 電源，模擬:3 V ~ 3.6 V 電壓 - 電源，數字:3 V ~ 3.6 V 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。