- 您現在的位置：買賣IC網 > PDF目錄361039 > LMC8101 (National Semiconductor Corporation) Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown PDF資料下載
參數資料
| 型號： | LMC8101 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| 中文描述： | 軌到軌輸入和輸出，在2.7運算放大器的micro SMD封裝，帶有關斷 |
| 文件頁數： | 7/15頁 |
| 文件大小： | 709K |
| 代理商： | LMC8101 |
Application Notes
(Continued)
Conversion Boards:
In order to ease the evaluation of tiny packages such as the
micro SMD, there is a conversion board (LMC8101CONV)
available to board designers. This board converts a micro
SMD device into an 8 pin DIP package (see Figure 2 Con-
version Board Pin out diagram) for easier handling and
evaluation. This board can be ordered from National Semi-
conductor by contacting http://www.national.com .
Increased Output Current:
Compared to the LMC7101, the LMC8101 has an improved
output stage capable of up to three times larger output
sourcing and sinking current. This improvement would allow
a larger output voltage swing range compared to the
LMC7101 when connected to relatively heavy loads. For
lower supply voltages this is an added benefit since it in-
creases the output swing range. For example, the LMC8101
can typically swing 2.5Vpp with 2mA sourcing and sinking
output current (Vs = 2.7V) whereas the LMC7101 output
swing would be limited to 1.9Vpp under the same conditions.
Also, compared to the LMC7101 in the SOT23 package, the
LMC8101 can dissipate more power because both the
MSOP and the micro SMD packages have 40% better heat
dissipation capability.
Lower 1/f noise:
The dominant input referred noise term for the LMC8101 is
the input noise voltage. Input noise current for this device is
of no practical significance unless the equivalent resistance
it looks into is 5M
or higher.
The LMC8101’s low frequency noise is significantly lower
than that of the LMC7101. For example, at 10Hz, the input
referred spot noise voltage density is 85 nV
pared to about 200nV
for the LMC7101. Over a fre-
quency range of 0.1Hz to 100Hz, the total noise of the
LMC8101 will be approximately 60% less than that of the
LMC7101.
Lower THD:
When connected to heavier loads, the LMC8101 has lower
THD compared to the LMC7101. For example, with 5V sup-
ply at 10KHz and 2Vpp swing (Av = 2), the LMC8101 THD
(0.2%) is 60% less than the LMC7101’s. The LMC8101 THD
can be kept below 0.1% with 3Vpp at the output for up to
10KHz (refer to the Typical Characteristics Plots).
Improving the Cap load drive capability:
This can be accomplished in several ways:
Output resistive loading increase:
The Phase Margin increases with increasing load (refer to
the Typical Characteristics Plots). When driving capacitive
loads, stability can generally be improved by allowing some
output current to flow through a load. For example, the cap
as com-
load drive capability can be increased from 8200pF to
16000pF if the output load is increased from 5K
to 600
(Av = +10, 25% overshoot limit, 10V supply).
Isolation resistor between output and cap load:
This resistor will isolate the feedback path (where excessive
phase shift due to output capacitance can cause instability)
from the capacitive load. With a 10V supply, a 100
isolation
resistor allows unlimited capacitive load without oscillation
compared to only 300pF without this resistor (Av = +1).
Higher supply voltage:
Operating the LMC8101 at higher supply voltages allows
higher cap load tolerance.At 10V, the LMC8101’s low supply
voltage cap load limit of 300pF improves to about 600pF (Av
= +1).
Closed loop gain increase:
As with all Op Amps, the capacitive load tolerance of the
LMC8101 increases with increasing closed loop gain. In ap-
plications where the load is mostly capacitive and the resis-
tive loading is light, stability increases when the LMC8101 is
operated at a closed loop gain larger than +1.
DS101240-89
FIGURE 2. micro SMD Conversion Board pin-out
www.national.com
7
相關PDF資料 |
PDF描述 |
|---|---|
| LMC8101BP | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| LMC8101BPX | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| LMC8101MM | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| LMC8101MMX | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| LMF100 | High Performance Dual Switched Capacitor Filter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMC8101BP | 功能描述:IC OP AMP R-R I/O 8-USMD RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| LMC8101BP/NOPB | 制造商:Texas Instruments 功能描述:OP Amp Single GP R-R I/O |
| LMC8101BPCONV | 功能描述:BOARD EVALUATION LMC8101BP RoHS:否 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| LMC8101BPX | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LMC8101BPX/NOPB | 功能描述:IC OP AMP R-R I/O 8-MICROSMD RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。