- 您現在的位置：買賣IC網 > PDF目錄361044 > LMX2430TMX (NATIONAL SEMICONDUCTOR CORP) PLLatinum Dual High Frequency Synthesizer for RF Personal Communications PDF資料下載
參數資料
| 型號： | LMX2430TMX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | XO, clock |
| 英文描述： | PLLatinum Dual High Frequency Synthesizer for RF Personal Communications |
| 中文描述： | PLL FREQUENCY SYNTHESIZER, 3000 MHz, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 37/49頁 |
| 文件大?。?/td> | 943K |
| 代理商： | LMX2430TMX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
1.0 Functional Description
(Continued)
1.8.4 Reference Divider and Feedback Divider Output
The outputs of the various N and R dividers can be moni-
tored by selecting the appropriate Ftest/LD word. This is
essential when performing OSCin or Fin sensitivity measure-
ments. Refer to the
LMX243x FinRF Sensitivity Test Setup
or
LMX243x OSCin Sensitivity Test Setup
sections for
more details. Note, the R and N outputs that are routed to
the Ftest/LD are R/2 and N/2 respectively. The internal /2
circuit is used to provide a 50% duty cycle. Refer to
Section
2.10
for more details on how to route the appropriate divider
output to the Ftest/LD pin.
1.9 FASTLOCK OUTPUT
The LMX243x Fastlock feature allows a faster loop response
time during lock aquisition. The loop response time (lock
time) can be approximately halved if the loop bandwidth is
doubled. In order to achieve this, the same gain/ phase
relationship should be maintained when the loop bandwidth
is doubled. When the FLoutRF or OSCout/ FLoutIF pins are
configured as FastLock outputs, an open drain device is
enabled. The open drain device switches in a resistor paral-
lel, and of equal value, to R2 of the external loop filter. The
loop bandwidth is effectively doubled and stability is main-
tained. Once locked to the correct frequency, the PLL will
return to a steady state condition.The LMX243x offers two
methods to achieve Fastlock: manual and automatic.
Manual Fastlock is achieved by increasing the charge pump
current from 1 mA (RF_CPG/ IF_CPG Bit = 0) in the steady
state mode, to 4 mA (RF_CPG/ IF_CPG Bit = 1) in Fastlock
mode. Automatic Fastlock is achieved by programming the
timeout counter register (RF_TOC/ IF_TOC) with the appro-
priate number of phase comparison cycles that the RF/ IF
synthesizer will spend in the Fastlock state. Refer to
Sec-
tions 2.6 and 2.9
for details on how to configure the
FLoutRF or OSCout/ FLoutIF output to an open drain Fast-
lock output.
1.10 COUNTER RESET
When the RF_RST/ IF_RST bit is enabled, both the feed-
back divider (RF_N/ IF_N) and reference divider (RF_R/
IF_R) are held at their load point. When the device is pro-
grammed to normal operation, both the feedback divider and
reference divder are enabled and resume counting in close
alignment to each other. Refer to
Sections 2.4.5 and 2.7.5
for more details.
1.11 POWER CONTROL
The LMX243x device can be asynchronously powered down
when the EN pin is set LOW, independent of the state of the
powerdown bits. Note that the OSCout/ FLoutIF pin can still
be enabled if the ENosc pin is set HIGH, independent of the
state of the EN pin. This capability allows the oscillator buffer
to be used as a crystal oscillator. When EN is set HIGH,
powerdown is controlled through the MICROWIRE. The
powerdown word is comprised of the
RF_PD
/
IF_PD
bit, in
conjuction with the
RF_CPT
/
IF_CPT
bit. The powerdown
control word is used to set the operating mode of the device.
Refer to
Sections 2.4.4, 2.5.4, 2.7.4
, and
2.8.4
for details on
how to program the RF or IF powerdown bits.
When either synthesizer is powered down, the respective
prescaler, phase detector, and charge pump circuit is dis-
abled. The CPoutRF/ CPoutIF, FinRF/ FinIF, and FinRF
*
pins are all forced to a high impedance state. The reference
divider and feedback divider circuits are held at the load
point during powerdown. The oscillator buffer is disabled
when the ENosc pin is set LOW. The OSCin pin is forced to
a HIGH state through an approximate 100 k
resistance
when this condition exists. When either synthesizer is acti-
vated, the respective prescaler, phase detector, charge
pump circuit, and the oscillator buffer are all powered up.
The feedback divider and reference divider are held at their
load point. This allows the reference oscillator, feedback
divider, reference divider and prescaler circuitry to reach
proper bias levels. After a finite delay, the feedback and
reference dividers are enabled and they resume counting in
close alignment (the maximum error is one prescaler cycle).
The MICROWIRE control register remains active and ca-
pable of loading and latching data while in powerdown
mode.
1.11.1 Synchronous Powerdown Mode
In this mode, the powerdown function is gated by the charge
pump. When the device is configured for synchronous pow-
erdown, the device will enter the powerdown mode upon
completion of the next charge pump pulse event.
1.11.2 Asynchronous Powerdown Mode
In this mode, the powerdown function is NOT gated by the
completion of a charge pump pulse event. When the device
is configured for asynchronous powerdown, the part will go
into powerdown mode immediately.
EN Pin
RF_CPT/
IF_CPT Bit
X
0
RF_PD/
IF_PD Bit
X
0
Operating Mode
0
1
Asynchronous Powerdown
PLL Active.
Normal Operation
PLL Active.
Charge Pump Output in High Impedance State
Synchronous Powerdown
Asynchronous Powerdown
1
1
0
1
1
0
1
1
1
Note:
X refers to a don’t care condition.
L
www.national.com
37
相關PDF資料 |
PDF描述 |
|---|---|
| LMX2433SLEX | PLLatinum Dual High Frequency Synthesizer for RF Personal Communications |
| LMX2434SLEX | PLLatinum Dual High Frequency Synthesizer for RF Personal Communications |
| LMX2531LQ1570E | PLLatinum High Performance Frequency Synthesizer System with Integrated VCO |
| LMX2531 | PLLatinum High Performance Frequency Synthesizer System with Integrated VCO |
| LMX2531LQ1650E | PLLatinum High Performance Frequency Synthesizer System with Integrated VCO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX2430TMX/NOPB | 功能描述:鎖相環 - PLL RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
| LMX2433EVAL | 功能描述:EVALUATION BOARD FOR LMX2433 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:PLLatinum™ 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| LMX2433EVAL/NOPB | 功能描述:時鐘和定時器開發工具 LMX2433 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V |
| LMX2433SLEX | 制造商:Texas Instruments 功能描述:3.6GHZ HI FREQ DUAL PLL SMD 2433 |
| LMX2433SLEX/NOPB | 功能描述:鎖相環 - PLL RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。