- 您現在的位置：買賣IC網 > PDF目錄361044 > LMX9820SBX (National Semiconductor Corporation) Bluetooth Serial Port Module PDF資料下載
參數資料
| 型號： | LMX9820SBX |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Bluetooth Serial Port Module |
| 中文描述： | 藍牙串行端口模塊 |
| 文件頁數： | 16/40頁 |
| 文件大小： | 567K |
| 代理商： | LMX9820SBX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
www.national.com
16
L
8.0 Digital Smart Radio
The LMX9820 Digital Smart Radio includes a high perfor-
mance, monolithic, radio transceiver optimized for Blue-
tooth communications systems.
The radio transceiver is a highly integrated design and
includes the Low Noise Amplifier (LNA), mixer, on-chip fil-
ters, 2.5 GHz
Σ
PLL, voltage controlled oscillator, Power
Amplifier (PA) driver, and modem functions. Digital modula-
tion and demodulation techniques are utilized for a robust
manufacturable design. Power management includes con-
trol over individual chip functions and internal voltage regu-
lation for optimum performance.
8.1 RADIO RECEIVER
The signal path of the RX architecture contains an internal
LNA and quadrature RF downconverting mixer at 2.5 GHz.
A low Intermediate Frequency (IF) receiver provides high
performance at low cost and low current consumption. The
IF demodulator is implemented digitally in combination with
a limiting amplifier.
8.2 LOW NOISE AMPLIFIER (LNA)
The on-board LNA is a single-ended structure designed
with a 50
input impedance for simple capacitive match-
ing. The LNA is closely integrated with the mixer providing
low noise and good immunity from blocking signals.
8.3 RX MIXER
The receive mixer is an image reject ring diode type mixer.
An internal low noise gain block is incorporated prior to the
mixer to achieve extremely low noise performance. A dif-
ferential IF output improves noise immunity while maintain-
ing a high intercept point.
8.4 CHANNEL SELECT FILTER
The IF circuitry is followed by an integrated complex active
bandpass filter that provides the required channel selectiv-
ity and image rejection. The I and Q outputs of the filter are
then converted to the digital domain using a limiter, discrim-
inator, and A/D converter.
8.5 LIMITER
The limiter circuit consists of I and Q limiting amplifiers that
provide the remaining gain in the receiver such that an
acceptable signal level exists at the frequency modulation
(FM) discriminator. Limiting amplification of the downcon-
verted wanted signal minimizes the input range require-
ments of the A/D converter.
8.6 FM DISCRIMINATOR
The limited signal is translated to digital format by using an
analog Frequency Shift Keying (FSK) demodulator and A/D
converter. The A/D converter extracts the RX signal at a
sample rate of 72.0 MHz.
8.7 RECEIVE SIGNAL STRENGTH INDICATOR
(RSSI)
The receive signal strength indicator (RSSI) signal is
derived from the input level to the limiter and covers a
range low detector level = -59dBm and high detector level
= -38dBm. The information is typically fed back to the
baseband controller via the serial interface.
8.8 RADIO TRANSMITTER
The signal path of the TX architecture contains an internal
modulator for 1 Mb/s GFSK (Gaussian Frequency Shift
Keying) modulation of the 2.5 GHz VCO. Closed loop
Σ
modulation is chosen since it is the most low power solu-
tion. The integrated pre-amplifier provides output levels
sufficient for Class 2 Bluetooth operation.
8.9 MODULATOR
An internal digital Gaussian filter provides the FSK modula-
tion waveform. A modulation input to the completely inte-
grated 2.5 GHz
Σ
PLL provides a consistent modulation
deviation. This eliminates the risks of open loop modulation
such as frequency drift and frequency offset.
8.10 TRANSMIT FREQUENCY OUTPUT
The transmit RF output is differential, and is connected to
the antenna through an integrated passive balun.
8.11 FREQUENCY SYNTHESIZERS
The 2.4 to 2.5GHz RF range is provided by an on-chip volt-
age controlled oscillator (VCO). A programmable 2.5 GHz
Σ
PLL selects the channel frequency. An internal crystal
oscillator can be configured with 12MHz crystal, or for
TCXO frequency input. Internal dividers provide internal
clocks and clock outputs to the baseband controller.
8.12 CRYSTAL CIRCUIT
Due to the need for clock accuracy, the LMX9820 has a
dedicated crystal oscillator. The LMX9820 uses the crystal
to supply a 12 MHz clock source to the baseband control-
ler. The 12 MHz is buffered, providing a receive data clock
to the baseband controller. It is also possible to configure
the crystal oscillator for input only when another high qual-
ity crystal oscillator is available in the system. The
LMX9820 can accommodate 12 MHz crystal.
8.13 EXTERNAL CRYSTAL OSCILLATORS
The LMX9820 contains a crystal driver circuit. This circuit
operates with an external crystal and capacitors to form an
oscillator. See Figure 10 on page 17 and Figure 11 on page
17. The LMX9820 also can operate with an external TCXO
(Temperature Compensated Crystal Oscillator).
8.13.1 Crystal
The crystal appears inductive near its resonant frequency.
It forms a resonant circuit with its load capacitors. The res-
onant frequency may be trimmed with the crystal load
capacitance.
1. Load Capacitance
For resonance at the correct frequency, the crystal should
be loaded with its specified load capacitance, which is the
value of capacitance used in conjunction with the crystal
unit. Load capacitance is a parameter specified by the
crystal, typically expressed in pF. The crystal circuit shown
in Figure 11 is composed of:
C1 (motional capacitance)
R1 (motional resistance)
L1 (motional inductance)
C0 (static or shunt capacitance)
The LMX9820 provides some of the load with internal
capacitors C
int
. The remainder must come from the exter-
nal capacitors labeled Ct1 and Ct2 as shown in Figure 10.
Ct1 and Ct2 should have the same value for best noise
相關PDF資料 |
PDF描述 |
|---|---|
| LP3882ESX-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ESX-1.5 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ESX-1.8 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ES-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX9830 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:BluetoothTM Serial Port Module |
| LMX9830DONGLE | 功能描述:藍牙/802.15.1 開發工具 LMX9830 BLUETOOTH EVAL KIT RoHS:否 制造商:Panasonic Electronic Components 產品:Bluetooth Evaluation Kit 工具用于評估:PAN1721 頻率:2.4 GHz 接口類型:I2C 工作電源電壓:2 V to 3.6 V |
| LMX9830DONGLE/NOPB | 制造商:Texas Instruments 功能描述:Evaluation Kit For Bluetooth Serial Port Module |
| LMX9830SM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:BluetoothTM Serial Port Module |
| LMX9830SM/NOPB | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。