- 您現在的位置：買賣IC網 > PDF目錄361045 > LP3882ES-1.5 (NATIONAL SEMICONDUCTOR CORP) 1.5A Fast-Response Ultra Low Dropout Linear PDF資料下載
參數資料
| 型號： | LP3882ES-1.5 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 1.5A Fast-Response Ultra Low Dropout Linear |
| 中文描述： | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.27 V DROPOUT, PSSO5 |
| 封裝： | TO-263, 5 PIN |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 326K |
| 代理商： | LP3882ES-1.5 |
Application Hints
(Continued)
UNDER VOLTAGE LOCKOUT
The bias voltage is monitored by a circuit which prevents the
regulator output from turning on if the bias voltage is below
approximately 4V.
SHUTDOWN OPERATION
Pulling down the shutdown (S/D) pin will turn-off the regula-
tor. Pin S/D must be actively terminated through a pull-up
resistor (10 k
to 100 k
) for a proper operation. If this pin
is driven from a source that actively pulls high and low (such
as a CMOS rail to rail comparator), the pull-up resistor is not
required. This pin must be tied to Vin if not used.
POWER DISSIPATION/HEATSINKING
A heatsink may be required depending on the maximum
power dissipation and maximum ambient temperature of the
application. Under all possible conditions, the junction tem-
perature must be within the range specified under operating
conditions. The total power dissipation of the device is given
by:
P
D
= (V
IN
V
OUT
)I
OUT
+ (V
IN
)I
GND
where I
GND
is the operating ground current of the device.
The maximum allowable temperature rise (T
Rmax
) depends
on the maximum ambient temperature (T
Amax
) of the appli-
cation, and the maximum allowable junction temperature
(T
Jmax
):
T
Rmax
= T
Jmax
T
Amax
The maximum allowable value for junction to ambient Ther-
mal Resistance,
θ
JA
, can be calculated using the formula:
θ
JA
= T
Rmax
/ P
D
These parts are available in TO-220 and TO-263 packages.
The thermal resistance depends on amount of copper area
or heat sink, and on air flow. If the maximum allowable value
of
θ
JA
calculated above is
≥
60 C/W for TO-220 package
and
60 C/W for TO-263 package no heatsink is needed
since the package can dissipate enough heat to satisfy these
requirements. If the value for allowable
θ
JA
falls below these
limits, a heat sink is required.
HEATSINKING TO-220 PACKAGE
The thermal resistance of a TO220 package can be reduced
by attaching it to a heat sink or a copper plane on a PC
board. If a copper plane is to be used, the values of
θ
JA
will
be same as shown in next section for TO263 package.
The heatsink to be used in the application should have a
heatsink to ambient thermal resistance,
θ
HA
≤ θ
JA
θ
CH
θ
JC
.
In this equation,
θ
is the thermal resistance from the case
to the surface of the heat sink and
θ
is the thermal resis-
tance from the junction to the surface of the case.
θ
JC
is
about 3C/W for a TO220 package. The value for
θ
CH
de-
pends on method of attachment, insulator, etc.
θ
CH
varies
between 1.5C/W to 2.5C/W. If the exact value is unknown,
2C/W can be assumed.
HEATSINKING TO-263 PACKAGE
The TO-263 package uses the copper plane on the PCB as
a heatsink. The tab of these packages are soldered to the
copper plane for heat sinking. The graph below shows a
curve for the
θ
of TO-263 package for different copper area
sizes, using a typical PCB with 1 ounce copper and no solder
mask over the copper area for heat sinking.
20063225
FIGURE 1.
θ
JA
vs Copper (1 Ounce) Area for TO-263
package
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LP3882ES-1.8 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ET-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ET-1.5 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ET-1.8 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3892ESX-1.8 | 1.5A Fast-Response Ultra Low Dropout Linear Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP3882ESX-1.2 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3882ESX-1.2/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3882ESX-1.5 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3882ESX-1.5/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3882ESX-1.8 | 功能描述:IC REG LDO 1.8V 1.5A TO-263-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:4V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.28V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:5-VFBGA 供應商設備封裝:5-uSMD 包裝:Digi-Reel® 其它名稱:LP2985AIBP-4.0DKR |
發布緊急采購，3分鐘左右您將得到回復。