- 您現在的位置：買賣IC網 > PDF目錄361045 > LP3892ESX-1.2 (NATIONAL SEMICONDUCTOR CORP) 1.5A Fast-Response Ultra Low Dropout Linear Regulators PDF資料下載
參數資料
| 型號： | LP3892ESX-1.2 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 1.5A Fast-Response Ultra Low Dropout Linear Regulators |
| 中文描述： | 1.216 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PSSO5 |
| 封裝： | MOLDED, TO-263, 5 PIN |
| 文件頁數： | 8/12頁 |
| 文件大小： | 315K |
| 代理商： | LP3892ESX-1.2 |
Application Hints
V
BIAS
RESTRICTIONS FOR PROPER START-UP
To prevent misoperation, ensure that V
is below 50mV
before start-up is initiated. This scenario can occur in sys-
tems with a backup battery using reverse-biased "blocking"
diodes which may allow enough leakage current to flow into
the V
BIAS
node to raise it’s voltage slightly above ground
when the main power is removed. Using low leakage diodes
or a resistive pull down can prevent the voltage at V
BIAS
from
rising above 50mV. Large bulk capacitors connected to
V
BIAS
may also cause a start-up problem if they do not
discharge fully before re-start is initiated (but only if V
BIAS
is
allowed to fall below 1V). A resistor connected across the
capacitor will allow it to discharge more quickly. It should be
noted that the probability of a "false start" caused by incor-
rect logic states is extremely low.
EXTERNAL CAPACITORS
To assure regulator stability, input and output capacitors are
required as shown in the Typical Application Circuit.
OUTPUT CAPACITOR
At least 10μF of output capacitance is required for stability
(the amount of capacitance can be increased without limit).
The output capacitor must be located less than 1 cm from
the output pin of the IC and returned to a clean analog
ground. The ESR (equivalent series resistance) of the output
capacitor must be within the "stable" range as shown in the
graph below over the full operating temperature range for
stable operation.
20069631
Minimum ESR vs Output Load Current
Tantalum capacitors are recommended for the output as
their ESR is ideally suited to the part’s requirements and the
ESR is very stable over temperature. Aluminum electrolytics
are not recommended because their ESR increases very
rapidly at temperatures below 10C.Aluminum caps can only
be used in applications where lower temperature operation
is not required.
A second problem with Al caps is that many have ESR’s
which are only specified at low frequencies. The typical loop
bandwidth of a linear regulator is a few hundred kHz to
several MHz. If an Al cap is used for the output cap, it must
be one whose ESR is specified at a frequency of 100 kHz or
more.
Because the ESR of ceramic capacitors is only a few milli
Ohms, they are not suitable for use as output capacitors on
LP389X devices. The regulator output can tolerate ceramic
capacitance totaling up to 15% of the amount of Tantalum
capacitance connected from the output to ground.
INPUT CAPACITOR
The input capacitor must be at least 10 μF, but can be
increased without limit. It’s purpose is to provide a low
source impedance for the regulator input. Ceramic capaci-
tors work best for this, but Tantalums are also very good.
There is no ESR limitation on the input capacitor (the lower,
the better). Aluminum electrolytics can be used, but their
ESR increase very quickly at cold temperatures. They are
not recommended for any application where temperatures
go below about 10C.
BIAS CAPACITOR
The 0.1μF capacitor on the bias line can be any good quality
capacitor (ceramic is recommended).
BIAS VOLTAGE
The bias voltage is an external voltage rail required to get
gate drive for the N-FET pass transistor. Bias voltage must
be in the range of 4.5 - 6V to assure proper operation of the
part.
UNDER VOLTAGE LOCKOUT
The bias voltage is monitored by a circuit which prevents the
regulator output from turning on if the bias voltage is below
approximately 4V.
SHUTDOWN OPERATION
Pulling down the shutdown (S/D) pin will turn-off the regula-
tor. Pin S/D must be actively terminated through a pull-up
resistor (10 k
to 100 k
) for a proper operation. If this pin
is driven from a source that actively pulls high and low (such
as a CMOS rail to rail comparator), the pull-up resistor is not
required. This pin must be tied to Vin if not used.
POWER DISSIPATION/HEATSINKING
A heatsink may be required depending on the maximum
power dissipation and maximum ambient temperature of the
application. Under all possible conditions, the junction tem-
perature must be within the range specified under operating
conditions. The total power dissipation of the device is given
by:
P
D
= (V
IN
V
OUT
)I
OUT
+ (V
IN
)I
GND
where I
GND
is the operating ground current of the device.
The maximum allowable temperature rise (T
Rmax
) depends
on the maximum ambient temperature (T
cation, and the maximum allowable junction temperature
(T
Jmax
):
T
Rmax
= T
Jmax
T
Amax
The maximum allowable value for junction to ambient Ther-
mal Resistance,
θ
JA
, can be calculated using the formula:
θ
JA
= T
Rmax
/ P
D
These parts are available in TO-220 and TO-263 packages.
The thermal resistance depends on amount of copper area
or heat sink, and on air flow. If the maximum allowable value
of
θ
JA
calculated above is
≥
60 C/W for TO-220 package
and
≥
60 C/W for TO-263 package no heatsink is needed
since the package can dissipate enough heat to satisfy these
requirements. If the value for allowable
θ
JA
falls below these
limits, a heat sink is required.
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LP3892ESX-1.5 | 1.5A Fast-Response Ultra Low Dropout Linear Regulators |
| LP3892ES-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear Regulators |
| LP3892ES-1.5 | 1.5A Fast-Response Ultra Low Dropout Linear Regulators |
| LP3892ES-1.8 | 1.5A Fast-Response Ultra Low Dropout Linear Regulators |
| LP3892ET-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP3892ET-1.2 | 制造商:Texas Instruments 功能描述:V REG LDO DR 1.5A 1.2V TO-220-5 制造商:Texas Instruments 功能描述:1.5A Fast LDO Reg. 1.2V,LP3892ET-1.2 |
| LP3892ET-1.2/NOPB | 功能描述:IC REG LDO 1.2V 1.5A TO-220-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品變化通告:Heatsink Pkg Change 09/Oct/2007 標準包裝:50 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:24V 輸入電壓:最高 40 V 電壓 - 壓降（標準）:2V @ 1A 穩壓器數量:1 電流 - 輸出:1A 電流 - 限制（最小）:- 工作溫度:0°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-220-3 供應商設備封裝:TO-220-3 包裝:管件 |
| LP3892ET-1.5 | 制造商:Texas Instruments 功能描述:V REG LDO DR 1.5A 1.5V TO-220-5 |
| LP3892ET-1.5/NOPB | 功能描述:IC REG LDO 1.5V 1.5A TO220-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品變化通告:Heatsink Pkg Change 09/Oct/2007 標準包裝:50 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:24V 輸入電壓:最高 40 V 電壓 - 壓降（標準）:2V @ 1A 穩壓器數量:1 電流 - 輸出:1A 電流 - 限制（最小）:- 工作溫度:0°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-220-3 供應商設備封裝:TO-220-3 包裝:管件 |
| LP3892ET-1.8 | 制造商:Texas Instruments 功能描述:V REG LDO DR 1.5A 1.8V TO-220-5 |
發布緊急采購，3分鐘左右您將得到回復。