- 您現在的位置：買賣IC網 > PDF目錄367592 > LSP2961 Precision Log Ratio Amplifier PDF資料下載
參數資料
| 型號： | LSP2961 |
| 英文描述： | Precision Log Ratio Amplifier |
| 中文描述： | 精密對數比例放大器 |
| 文件頁數： | 1/6頁 |
| 文件大小： | 145K |
| 代理商： | LSP2961 |
Advance Data Sheet
September 2001
LSP2961
Precision Log Ratio Amplifier
Features
I
Seven decades (1 nA to 10 mA) typical input range
I
Internal scale factor K = 1 ± 2% (K externally
adjustable):
(eq. 1)
I
Internal trimmed reference current
(I
REF
= 1 μA ± 5%, externally adjustable)
I
Maximum ±100 mV output offset (externally
adjustable)
I
Minimal external components
I
±5 V power supply
I
TSSOP small package
Applications
I
Optical light density measurement
I
Log, log ratio computation
I
Data linearization
Description
The LSP2961 is a single-channel precision logarithm
and log ratio integrated circuit powered by +5 V and
–5 V power supplies. The voltage output of the
amplifier is a logarithmic function of the ratio of a
reference current (I
REF
) over the input current (I
IN
).
The scale factor is set internally to 1 V/decade, and
is further adjustable by adding an external resistor.
The input dynamic range for the amplifier is a six-
decade (1 nA to 1 mA) minimum, with seven-decade
(1 nA to 10 mA) and eight-decade (100 pA to 10 mA)
operation available with increased conformity error.
The amplifier has an internal trimmed reference 1
μ
A
±
5% current source that is also externally adjustable
using an external resistor. The output offset voltage
is 100 mV maximum and can be nulled using an
external potentiometer.
The input current is applied to the IN pin and the
corresponding output is taken from the OUTPUT pin.
For a 1 V/decade application in a stable temperature
environment, no external components are required to
obtain the specified performance. For an application
that a scale factor other than 1 V/decade is required,
an external resistor connecting the SCALE FACTOR
pin to either the OUTPUT pin or GND will result in
less or more than 1 V/decade for the scale factor.
The amplifier’s output can range from (V
CC
– 1 V) to
(V
EE
+ 1 V). This is ideal for the control in optical
density measurements, and in other situations such
as precision logarithm calculations. Each amplifier
has an internally trimmed reference current of 1
μ
A.
This reference current can be changed using an
external resistor connecting to the I
REF_ADJ
pin, and
either V
CC
or GND, depending on the need to
increase or decrease the reference current.
Additionally, the maximum output offset voltage is
±100 mV. This can be nulled using an external
potentiometer connected between the ±5 V supplies
and the wiper connected to the V
OS_ADJ
pin. The
internal block diagram is shown in Figure 1.
The LSP2961 is available in a 3 mm x 3 mm TSSOP
package. The 8-pin LSP2961 requires one negative
5 V power supply (V
EE
) and one positive 5 V power
supply (V
CC
). Refer to Table 1 for detailed pin
information. Figure 3 references the external pin
connections.
OUTPUT
K
I
IN
-------------
log
×
=
相關PDF資料 |
PDF描述 |
|---|---|
| LSPK370NR | Optoelectronic |
| LSGK370LO | Optoelectronic |
| LSPK372PO | Optoelectronic |
| LSGK372RO | Optoelectronic |
| LSPT670GO | Optoelectronic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LSP2B | 功能描述:限位開關 Limit SW/Double Pole Plug-in RoHS:否 制造商:Honeywell 觸點形式:SPDT 執行器:Non-Contact 電流額定值:30 mA 電壓額定值 AC: 電壓額定值 DC:3.6 V 工作力:10 g IP 等級:IP 67 NEMA 額定值:1, 4, 12, 13 端接類型:4-Pin M12 Connector 安裝:SMD/SMT |
| LSP2B-1B | 功能描述:限位開關 LIMIT SWITCH RoHS:否 制造商:Honeywell 觸點形式:SPDT 執行器:Non-Contact 電流額定值:30 mA 電壓額定值 AC: 電壓額定值 DC:3.6 V 工作力:10 g IP 等級:IP 67 NEMA 額定值:1, 4, 12, 13 端接類型:4-Pin M12 Connector 安裝:SMD/SMT |
| LSP32-K2-RGBA | 制造商:Dialight 功能描述:LED MODULE 32X K2 RGBA |
| LSP-32K2-RGBW | 制造商:Dialight 功能描述: |
| LSP32-K2-RGBW | 制造商:Dialight 功能描述:LED MODULE 32X K2 RGBW |
發布緊急采購，3分鐘左右您將得到回復。