- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4211IMS8 (Linear Technology)IC CONTROLLER HOT SWAP 8-MSOP Datasheet資料下載
參數資料
| 型號： | LTC4211IMS8 |
| 廠商： | Linear Technology |
| 文件頁數： | 31/40頁 |
| 文件大小： | 321K |
| 描述： | IC CONTROLLER HOT SWAP 8-MSOP |
| 標準包裝： | 50 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.5 V ~ 16.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LTC4211
31
4211fb
APPLICATIONS INFORMATION
1
2
3
4
5
10
9
8
7
6
FAULT
V
CC
SENSE
GATE
FB
RESET
ON
FILTER
TIMER
GND
LTC4211
Z1 = 1SMA10A OR SMAJ10A
Z2 = 1N4691
* OPTIONAL
Q1
Si4410DY
R1
36k
V
OUT
5V
5A
R2
15k
C
LOAD
4211 F23
R
SENSE
0.007?/DIV>
+
C
TIMER
10nF
C
FILTER
47pF
Z2
6.2V
LONG
5V
GND
FAULT
LONG
PCB EDGE
CONNECTOR
(MALE)
BACKPLANE
CONNECTOR
(FEMALE)
SHORT
SHORT
SHORT
RESET
ON/OFF
R3
10?/DIV>
Z1*
C1
0.1糉
R5
10k
R6
10k
R7
10k
R4
10k
SUPPLY OVERVOLTAGE DETECTION/
PROTECTION USING FILTER PIN
In addition to using external protection devices around the
LTC4211 for large scale transient protection, low power
Zener diodes can be used with the LTC4211s FILTER
pin to act as a supply overvoltage detection/protection
circuit on either the high side (input) or low side (output)
of the external pass transistor. Recall that internal control
circuitry keeps the LTC4211 GATE voltage from ramping
up if V
FILTER
> 1.156V, or when an external fault condition
(V
FILTER
> 1.236V) causes FAULT to be asserted low.
High Side (Input) Overvoltage Protection
As shown in Figure 23, a low power Zener diode can
be used to sense an overvoltage condition on the input
(high) side of the main 5V supply. In this example, a low
bias current 1N4691 Zener diode is chosen to protect the
system. Here, the Zener diode is connected from V
CC
to
the LTC4211s FILTER pin (Pin 3 MS). If the input volt-
age to the system is greater than 6.8V during start-up,
the voltage on the FILTER pin is pulled higher than its
1.156V threshold. As a result, the GATE pin is not allowed
to ramp and the second timing cycle will not commence
until the supply overvoltage condition is removed. Should
the supply overvoltage condition occur during normal
operation, internal control logic would trip the electronic
circuit breaker and the GATE would be pulled to ground,
shutting OFF the external pass transistor. If a lower supply
overvoltage threshold is desired, use a Zener diode with
a smaller breakdown voltage.
A timing diagram for illustrating LTC4211 operation under a
high side overvoltage condition is shown in Figure 24. The
start-up sequence in this case (between Time Points 1 and
2) is identical to any other start-up sequence under normal
operating conditions. At Time Point 2A, the input supply
voltage causes the Zener diode to conduct thereby forcing
V
FILTER
> 1.156V. At Time Point 3, FAULT is asserted low
and the TIMER pin voltage ramps down. At Time Point 4,
the LTC4211 checks if V
FILTER
< 1.156V. FAULT is asserted
low (but not latched) to indicate a start-up failure. The
start-up sequence only resumes with the second timing
cycle at Time Point 5 when the input overvoltage condition
is removed. At this point in time, the GATE pin voltage is
allowed to ramp up, FAULT is pulled to logic high and the
circuit breaker is armed. At any time after Time Point 5,
should a supply overvoltage condition develop (V
FILTER
>
1.236V), the electronic circuit breaker will trip, the GATE
will be pulled low to turn off the external MOSFET and
FAULT will be asserted low and latched. This sequence is
shown in detail at Time Point B.
Figure 23. LTC4211MS High Side Overvoltage Protection Implementation
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4212IMS#TRPBF | IC CTRLR HOTSWAP TIMEOUT 10MSOP |
| LTC4214-1IMS#TRPBF | IC CTRLR HOTSWAP NEGVOLT 10MSOP |
| LTC4215IUFD#PBF | IC CNTRLR HOT SWAP 24-QFN |
| LTC4216IDE#TRPBF | IC CNTRLR HOT SWAP 12-DFN |
| LTC4221IGN#TRPBF | IC CTRLR HOTSWAP DUAL 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4211IMS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4211IMS8#TR | 功能描述:IC CONTROLLER HOT SWAP 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4211IMS8#TRPBF | 功能描述:IC CONTROLLER HOT SWAP 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4211IS8 | 功能描述:IC CTRLR HOTSWAP CURR CTRL 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4211IS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。