- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4241IGN#PBF (Linear Technology)IC CTRLR HOTSWAP 3.3V AUX 20SSOP Datasheet資料下載
參數資料
| 型號： | LTC4241IGN#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 14/16頁 |
| 文件大小： | 279K |
| 描述： | IC CTRLR HOTSWAP 3.3V AUX 20SSOP |
| 標準包裝： | 55 |
| 類型： | 熱交換控制器 |
| 應用： | PCI，PCI-X |
| 內部開關： | 無 |
| 電源電壓： | 3.3V，5V，±12V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
LTC4241
14
sn4241 4241f
Table 4. N-Channel Power MOSFET Selection Guide
CURRENT
PART NUMBER
PACKAGE
V
DS
MAX
V
GS
MAX
R
DS(on)
MANUFACTURER
RATING
8.0A
Si4412ADY
SO-8
30V
?0V
0.024&
Vishay-Siliconix
3.5A
Si2306DS
SOT-23
30V
?0V
0.057&
Vishay-Siliconix
10A
Si4410DY
SO-8
30V
?0V
0.013&
Vishay-Siliconix
13A
IRF7413
SO-8
30V
?0V
0.011&
International Rectifier
2.7A
FDN 359AN
SOT-23
30V
?0V
0.046&
Fairchild Semiconductor
Electronic Circuit Breaker for 3.3V Auxiliary Supply
An electronic circuit breaker is used to protect against
excessive load current and short-circuits on the 3.3V
auxiliary supply. The load current is monitored by placing
a sense resistor R3 between AUXIN and AUXSENSE as
shown in Figure 1. The circuit breaker trip threshold is
50mV and exhibits a response time of 8祍. Unlike the PCI
supplies which use the current foldback limit with circuit
breaker during short-circuits, here the circuit breaker will
trip and immediately pull AUXGATE to ground if the
voltage between AUXIN and AUXSENSE exceeds 50mV for
more than 8祍. The external N-channel transistor is turned
off and FAULT is pulled low. The circuit breaker is reset
when AUXON is cycled low then high, or the AUXIN supply
is cycled. If the circuit breaker feature is not required, the
AUXSENSE pin can be shorted to AUXIN.
The trip current of the circuit breaker is set by:
I
TRIP
= 50mV/R3
As a design aid, the trip current for commonly used values
for R3 is given in Table 3.
Table 3. I
TRIP
vs R3
R3 (&)
I
TRIP
0.05
1A
0.06
833mA
0.07
714mA
0.08
625mA
0.09
556mA
0.1
500mA
If more than 8祍 of response time is needed to reject
supply current ripple noise, an external resistor, R
F
, of
20& and capacitor, C
F
, of 1礔 (Figure 6) can be added to
the AUXSENSE circuit. This will give a delay of 15祍.
Supply Bypass Capacitors
In motherboard applications, large bypass capacitors are
recommended at each of the system power supplies to
minimize supply glitches as a result of board insertion. A
supply bypass capacitor of e100礔 at 12V
IN
connection is
recommended.
APPLICATIO S I FOR ATIO
U
U
U
Figure 8. Making PCB Connections to
the Sense Resistor for the 5V Rail
SENSE RESISTOR
CURRENT FLOW
FROM SUPPLY
CURRENT FLOW
TO LOAD
5V
IN
5V
SENSE
TRACK WIDTH W:
0.03" PER AMPERE
ON 1 OZ COPPER FOIL
W
4241 F08
PCB Layout Considerations for the Sense Resistor
For proper circuit breaker operation, 4-wire Kelvin-sense
connections between the sense resistor and the LTC4241s
5V
IN
and 5V
SENSE
pins, 3V
IN
and 3V
SENSE
pins and AUXIN
and AUXSENSE pins are strongly recommended. The
drawing in Figure 8 illustrates the correct way of making
connections between the LTC4241 and the sense resistor.
PCB layout should be balanced and symmetrical to mini-
mize wiring errors. In addition, the PCB layout for the
sense resistors and the power MOSFETs should include
good thermal management techniques for optimal sense
resistor power dissipation.
Power MOSFET and Sense Resistor Selection
Table 4 lists some available N-channel power MOSFETs .
Table 5 lists some current sense resistors that can be used
with the LTC4241s circuit breakers. Table 6 lists the
supplier web site addresses for discrete components
mentioned throughout this datasheet.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4242CUHF#TRPBF | IC CNTRLR HOT SWAP 38-QFN |
| LTC4244CGN-1#TRPBF | IC CTRLR HOTSWAP PCI 20-SSOP |
| LTC4245CG#TRPBF | IC CNTRLR HOT SWAP 36-SSOP |
| LTC4251-2CS6#TRPBF | IC CTRLR HOTSWAP NEGVOLT SOT23-6 |
| LTC4252A-1IMS#TRPBF | IC CNTRLR HOTSWAP NEGVOLT 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4242 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Slot Hot Swap Controller for PCI Express |
| LTC4242CG | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Slot Hot Swap Controller for PCI Express |
| LTC4242CG#PBF | 功能描述:IC CNTRLR HOT SWAP 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC4242CG#TRPBF | 功能描述:IC CNTRLR HOT SWAP 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC4242CUHF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Slot Hot Swap Controller for PCI Express |
發布緊急采購，3分鐘左右您將得到回復。