
General Description
The MAX1165 evaluation kit (EV kit) is an assembled
and tested circuit board that demonstrates the
MAX1165 analog-to-digital converter. The EV kit can
also evaluate the MAX1065/MAX1066 and MAX1165/
MAX1166. Request free samples of the desired parts
when ordering the MAX1165 EV kit.
Features
o
Proven PC Board Layout
o
Convenient On-Board Test Points
o
Fully Assembled and Tested
Quick Start
Recommended Equipment
MAX1165 EV kit
Two DC power supplies, 5V at 10mA
Programmable signal generator, such as Tektronix
DG2020A
Logic analyzer (optional)
Reconstruction DAC (optional)
Procedure
The MAX1165 EV kit is fully assembled and tested.
Follow these steps to verify board operation.
Do not turn
on the power supply until all connections are com-
pleted.
1) Ensure that JU1, JU2, and JU3 are open (see
Table 1).
2) With the power off, connect the first 5VDC power
supply between AVDD and AGND.
3) With the power off, connect the second 5VDC power
supply between DVDD and DGND.
Note:
DGND
and AGND are connected on the MAX1165 EV kit
board. To avoid ground loops, do not connect
AGND to DGND at any other location.
4) Configure the pattern generator to produce the
appropriate read/convert (R/
C
) and conversion start
(
CS
) waveforms. Refer to Figure 2 in the MAX1165
data sheet.
5) Connect the pattern generator
CS
output across
jumper JU4.
6) Connect the pattern generator R/
C
output across
jumper JU5.
7) Connect logic analyzer or other digital data capture
system to header H1. The least significant bit, D0,
appears on H1 pin 1, and the end-of-conversion out-
put strobe (
EOC
) appears across jumper JU6 (see
Table 2).
8) Turn on the power supplies and enable the pattern
generator.
9) Apply 0 to 4.096V analog input signal between
pads AIN and AGND. Capture digital data from
header H1.
E
MAX1165 Evaluation Kit
________________________________________________________________
Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
19-2558; Rev 0; 6/02
Component List
Ordering Information
PART
TEMP RANGE
0
°
C to +70
°
C
IC PACKAGE
28 TSSOP
MAX1165EVKIT
Note:
Please indicate that you are using the MAX1165 when con-
tacting these component suppliers.
SUPPLIER
Taiyo
Yuden
PHONE
FAX
WEBSITE
800-348-2496 847-925-0899
w w w t- yud en.com
DESIGNATION
QTY
DESCRIPTION
C1, C2, C11,
C12
4
10μF, 10V X7R ceramic capacitors
Taiyo Yuden LMK325BJ106MN
C3, C4, C5, C8,
C9, C10
6
0.1μF, 10V X7R ceramic capacitors
C6
1
4.7μF, 10V X7R ceramic capacitor
Taiyo Yuden JMK212BJ475KG
C7
1
4
1
6
1
1
1
1
1
1
1
1
0.01μF ceramic capacitor
Socket-pin receptacles
2
×
16 dual-row vertical header
2-pin headers
100k
±5% resistor
4.7
±5% resistor
MAX1165BEUI
Hex Schmitt trigger buffer 74HC14
MAX4430ESA
MAX1165 EV kit PC board
MAX1165 data sheet
MAX1165 EV kit data sheet
C7, R2
H1
JU1
–
JU6
R1
R2
U1
U2
U3
None
None
None
Component Supplier