- 您現在的位置：買賣IC網 > Datasheet目錄55 > MAX1479ATE+T (Maxim Integrated)IC TRANSM ASK/FSK 16-TQFN Datasheet資料下載
參數資料
| 型號： | MAX1479ATE+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 265K |
| 描述： | IC TRANSM ASK/FSK 16-TQFN |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 頻率： | 300MHz ~ 450MHz |
| 應用： | ISM，車庫門開啟器，RKE |
| 調制或協議： | ASK，FSK，OOK |
| 數據傳輸率 - 最大： | 100 kbps |
| 功率 - 輸出： | 2.7dBm ~ 16.1dBm |
| 電流 - 傳輸： | 6.7mA ~ 10.5mA |
| 數據接口： | PCB，表面貼裝 |
| 天線連接器： | PCB，表面貼裝 |
| 電源電壓： | 2.1 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 16-WFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
300MHz to 450MHz Low-Power,
Crystal-Based +10dBm ASK/FSK Transmitter
6 _______________________________________________________________________________________
Detailed Description
The MAX1479 is a highly integrated ASK/FSK transmit-
ter operating over the 300MHz to 450MHz frequency
band. The device requires only a few external compo-
nents to complete a transmitter solution. The MAX1479
includes a complete PLL and a highly efficient power
amplifier. The device can be set into a 0.2nA low-power
shutdown mode.
Shutdown Mode
ENABLE (pin 4) is internally pulled down with a 20礎
current source. If it is left unconnected or pulled low,
the MAX1479 goes into a low-power shutdown mode.
In this mode, the supply current drops to 0.2nA. When
ENABLE is high, the device is enabled and is ready for
transmission after 200祍 (frequency settles to within
50kHz).
The 200祍 turn-on time of the MAX1479 is mostly domi-
nated by the crystal oscillator startup time. Once the
oscillator is running, the 300kHz PLL bandwidth allows
fast frequency recovery during power-amplifier toggling.
Mode Selection
MODE (pin 2) sets the MAX1479 in either ASK or FSK
mode. When MODE is set low, the device operates as
an ASK transmitter. If MODE is set high, the device
operates as an FSK transmitter. In the ASK mode, the
DIN pin controls the output of the power amplifier. A
logic low on DIN turns off the PA, and a logic high turns
on the PA. In the FSK mode, a logic low on the DIN pin
is represented by the low FSK frequency, and a logic-
high input is represented by the high FSK frequency.
(The ASK carrier frequency and the lower FSK frequen-
cy are the same.) The deviation is proportional to the
crystal load impedance and pulling capacitance. The
maximum frequency deviation is 55kHz for f
RF
=
315MHz and 80kHz for f
RF
= 433MHz.
Pin Description
PIN
NAME
DESCRIPTION
1
V
DD
Supply Voltage. Bypass to GND with a 10nF and 220pF capacitor as close to the pin as possible.
2
MODE
Mode Select. A logic low on MODE enables the device in ASK mode. A logic high on MODE enables the
device in FSK mode.
3
DIN
Data Input. Power amplifier is on when DIN is high in ASK mode. Frequency is high when DIN is high in
FSK mode.
4
ENABLE Standby/Power-Up Input. A logic low on ENABLE sets the device in standby mode.
5
CLKOUT Buffered Clock Output. Programmable through CLK0 and CLK1. See Table 1.
6
V
DD_
PA
Power-Amplifier Supply Voltage. Bypass to GND with a 10nF and 220pF capacitor as close to the pin as
possible.
7
ROUT
Envelope-Shaping Output. ROUT controls the power-amplifier envelope rise and fall. Bypass to GND with a
680pF and 220pF capacitor as close to the pin as possible.
8
PAOUT
Power-Amplifier Output. Requires a pullup inductor to the supply voltage, which can be part of the output-
matching network to an antenna.
9
CLK0
1st Clock Divider Setting. See Table 1.
10
CLK1
2nd Clock Divider Setting. See Table 1.
11
DEV0
1st FSK Frequency-Deviation Setting. See Table 2.
12
DEV1
2nd FSK Frequency-Deviation Setting. See Table 2.
13
DEV2
3rd FSK Frequency-Deviation Setting. See Table 2.
14
XTAL1
1st Crystal Input. f
RF
= 32 x f
XTAL
.
15
XTAL2
2nd Crystal Input. f
RF
= 32 x f
XTAL
.
16
GND
Ground. Connect to system ground.
EP
Exposed Ground Pad. EP is the power amplifiers ground. It must be connected to PCB through a low-
inductance ath.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX19790ETX+T | IC 250MHZ - 4GHZ VAR ATTEN |
| MAX19792ETX+ | ATTENUATR 46DB 50OHM 4GHZ 36TQFN |
| MAX19794ETX+ | ATTENUATR 46DB 50OHM 4GHZ 36TQFN |
| MAX2365ETM+T | IC TRANSMITTER QUAD 48TQFN-EP |
| MAX2369EGM+TD | IC TRANSMITTER QUAD 48QFN-EP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1479EVKIT-315 | 功能描述:射頻開發工具 MAX1479 Eval Kit RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| MAX1479EVKIT-433 | 功能描述:射頻開發工具 MAX1479 Eval Kit RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| MAX147ACAP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX147ACAP+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX147ACAP+T | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。