- 您現在的位置：買賣IC網 > Datasheet目錄42 > MAX1619MEE+ (Maxim Integrated)IC TEMP SENSOR W/ALARM 16-QSOP Datasheet資料下載
參數資料
| 型號： | MAX1619MEE+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 9/20頁 |
| 文件大小： | 303K |
| 描述： | IC TEMP SENSOR W/ALARM 16-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS |
| 標準包裝： | 100 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±3.5°C 本地（最大），±5°C 遠程（最大） |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | 2 線串行，I²C?/SMBUS? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 管件 |
PC Board Layout
1) Place the MAX1619 as close as practical to the
remote diode. In a noisy environment, such as a
computer motherboard, this distance can be 4 inch-
es to 8 inches (typical) or more as long as the worst
noise sources (such as CRTs, clock generators,
memory buses, and ISA/PCI buses) are avoided.
2) Do not route the DXPDXN lines next to the deflec-
tion coils of a CRT. Also, do not route the traces
across a fast memory bus, which can easily intro-
duce +30癈 error, even with good filtering.
Otherwise, most noise sources are fairly benign.
3) Route the DXP and DXN traces in parallel and in
close proximity to each other, away from any high-
voltage traces such as +12V
DC
. Leakage currents
from PC board contamination must be dealt with
carefully, since a 10M& leakage path from DXP to
ground causes about +1癈 error.
4) Connect guard traces to GND on either side of the
DXPDXN traces (Figure 2). With guard traces in
place, routing near high-voltage traces is no longer
an issue.
5) Route through as few vias and crossunders as possi-
ble to minimize copper/solder thermocouple effects.
6) When introducing a thermocouple, make sure that
both the DXP and the DXN paths have matching
thermocouples. In general, PC board-induced ther-
mocouples are not a serious problem. A copper-sol-
der thermocouple exhibits 3礦/癈, and it takes
about 200礦 of voltage error at DXPDXN to cause
a +1癈 measurement error. So, most parasitic ther-
mocouple errors are swamped out.
7) Use wide traces. Narrow ones are more inductive
and tend to pick up radiated noise. The 10 mil
widths and spacings recommended in Figure 2
arent absolutely necessary (as they offer only a
minor improvement in leakage and noise), but try to
use them where practical.
8) Keep in mind that copper cant be used as an EMI
shield, and only ferrous materials, such as steel, work
well. Placing a copper ground plane between the
DXP-DXN traces and traces carrying high-frequency
noise signals does not help reduce EMI.
PC Board Layout Checklist
" Place the MAX1619 close to a remote diode.
" Keep traces away from high voltages (+12V bus).
" Keep traces away from fast data buses and CRTs.
" Use recommended trace widths and spacings.
" Place a ground plane under the traces.
" Use guard traces flanking DXP and DXN and con-
necting to GND.
" Place the noise filter and the 0.1礔 V
CC
bypass
capacitors close to the MAX1619.
" Add a 200& resistor in series with V
CC
for best noise
filtering (see Typical Operating Circuit).
Twisted Pair and Shielded Cables
For remote-sensor distances longer than 8 inches, or in
particularly noisy environments, a twisted pair is recom-
mended. Its practical length is 6 feet to 12 feet (typical)
before noise becomes a problem, as tested in a noisy
electronics laboratory. For longer distances, the best
solution is a shielded twisted pair like that used for audio
microphones. For example, the Belden 8451 works well
in a noisy environment for distances up to 100 feet.
Connect the twisted pair to DXP and DXN and the shield
to GND, and leave the shields remote end unterminated.
Excess capacitance at DX_ limits practical remote sen-
sor distances (see Typical Operating Characteristics).
For very long cable runs, the cables parasitic capaci-
tance often provides noise filtering, so the 2200pF
capacitor can often be removed or reduced in value.
Cable resistance also affects remote-sensor accuracy;
1& series resistance introduces about +1/2癈 error.
Low-Power Standby Mode
Standby mode disables the ADC and reduces the sup-
ply-current drain to 3礎 (typical). Enter standby mode
by forcing the STBY pin low or via the RUN/STOP bit in
the configuration byte register. Hardware and software
standby modes behave almost identically: all data is
retained in memory, and the SMB interface is alive and
listening for reads and writes. The only difference is
that in hardware standby mode, the one-shot command
does not initiate a conversion.
Standby mode is not a shutdown mode. With activity on
the SMBus, extra supply current is drawn (see Typical
Operating Characteristics). In software standby mode,
Remote/Local Temperature Sensor with Dual-
Alarm Outputs and SMBus Serial Interface
_______________________________________________________________________________________ 9
MINIMUM
10 MILS
10 MILS
10 MILS
10 MILS
GND
DXN
DXP
GND
Figure 2. Recommended DXP/DXN PC Traces
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1765EUE+ | IC REG DL BST/LINEAR 16TSSOP |
| MAX1989MUE+ | IC TEMP SENSOR REMOTE 16TSSOP |
| MAX31723MUA+ | IC THERMOMETER/STAT SPI-3W 8UMAX |
| MAX31826MUA+T | IC TEMP SENSOR DIGITAL 8UMAX |
| MAX4006EUT+T | IC CURRENT MONITOR 1% SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1619MEE+ | 功能描述:板上安裝溫度傳感器 Remote/Local Temp Sensor w Dual Alarm RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1619MEE+T | 功能描述:板上安裝溫度傳感器 Remote/Local Temp Sensor w Dual Alarm RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX1619MEE-T | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| MAX161AC/D | 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX161ACPI | 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。