- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5903LAETT+T (Maxim Integrated)IC HOT-SWAP CONTROLLER 6-TDFN Datasheet資料下載
參數資料
| 型號： | MAX5903LAETT+T |
| 廠商： | Maxim Integrated |
| 文件頁數： | 8/14頁 |
| 文件大小： | 333K |
| 描述： | IC HOT-SWAP CONTROLLER 6-TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | Simple Swapper™ |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 9 V ~ 72 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-WDFN 裸露焊盤 |
| 供應商設備封裝： | 6-TDFN 裸露焊盤（3x3） |
| 包裝： | 帶卷 (TR) |
Turn-On and Turn-Off Delays
After power is applied, or ON/OFF is released, there is
a 150ms delay (t
ON
) before the gate ramp is started.
This delay is also the automatic restart time delay.
In the event of a circuit-breaker condition or an over-
temperature fault condition, the turn-off delay is less
than 4祍. An undervoltage condition must exist for at
least 10ms (t
OFF
) before the MAX5902/MAX5903 turns
off the external MOSFET. ON/OFF must be held low for
at least 10ms (t
OFF
) before the MAX5902/MAX5903
turns off the external MOSFET. Turn-off delay minimizes
spurious shutdowns due to noisy signals or momentary
voltage spikes, as well as preventing accidental reset-
ting of the circuit-breaker latch (MAX5902L/MAX5903L).
Thermal Shutdown
A thermal shutdown feature helps protect the external
MOSFET. If the die temperature of the MAX5902/
MAX5903 exceeds +125癈, the MOSFET is turned off.
For accurate performance the MAX5902/MAX5903
must be in close thermal contact with the external MOS-
FET. See the Layout Guidelines section for information.
Due to the low power dissipation of the
MAX5902/MAX5903, its junction temperature will typi-
cally be within a few degrees of the MOSFET. All ver-
sions of the MAX5902/MAX5903 automatically restart
from a temperature fault when the junction temperature
drops below +110癈.
Undervoltage Lockout
The MAX5902/MAX5903 turns off the external MOSFET
if the magnitude of the input voltage is below the level
set by ON/OFF for longer than 10ms (t
OFF
). If ON/OFF
is left unconnected, the lockout voltage (V
UVLO
)
defaults to 31.5V. V
UVLO
may also be set to any value
within the power-supply range by using external resis-
tors. To set the lockout voltage to a value between +9V
and +72V use a resistor divider connected between V
S
and GND, with the center node of the divider connect-
ed to ON/OFF. For example, use a 3k& resistor (R1 in
Figure 3) from ON/OFF to GND and calculate the other
resistor, R2, using:
where V
UVLO
is the desired lockout voltage, and
V
ON/OFF
is the ON/OFF reference threshold specified in
the Electrical Characteristics table (typically 1.26V).
Figure 3 shows an example circuit with V
UVLO
set for
+18V. To defeat the UVLO simply connect a single
100k& resistor between ON/OFF and V
S
, as shown in
Figure 6.
The Power-Good Output
The power-good output, PGOOD (PGOOD), is open-
drain and asserts when the external MOSFET is fully
enhanced and V
SD
is less than the circuit-breaker
threshold (V
CB
). For versions without the circuit-breaker
function (MAX5902N/MAX5903N), PGOOD (PGOOD)
asserts when the external MOSFET is fully enhanced.
PGOOD (PGOOD) deasserts within 4祍 when a circuit-
breaker event occurs or if the die temperature exceeds
+125癈. PGOOD (PGOOD) deasserts if V
S
< V
UVLO
for
longer than 10ms or ON/OFF is held low for longer than
10ms.
The MAX5902 PGOOD is active-low and the MAX5903
PGOOD is active-high. Both are open-drain n-channel
MOSFETs with their sources connected to GND, and
can withstand up to +72V.
R
R
V
V
UVLO
ON OFF
2
1
1
=
?/DIV>
?/DIV>
?/DIV>
主站蜘蛛池模板：
大邑县|
应城市|
南陵县|
建始县|
普陀区|
龙海市|
广水市|
青神县|
商河县|
资溪县|
农安县|
赣榆县|
连江县|
彰化县|
丰台区|
临城县|
皮山县|
鹤山市|
苏州市|
哈密市|
濉溪县|
永新县|
莫力|
桃源县|
高清|
光山县|
吉木乃县|
双峰县|
富源县|
开鲁县|
上饶市|
长沙县|
江都市|
福安市|
乌拉特后旗|
韶关市|
苏州市|
昌都县|
萨嘎县|
肥西县|
黔西县|
?/DIV>
?/DIV>
?/DIV>
?/DIV>
/
+72V, SOT23/TDFN, Simple Swapper Hot-Swap
Controllers
8 _______________________________________________________________________________________
HOT-SWAP CONTROLLER
+9V TO +72V
V
S
GND
100k&
MAX5902
GND
ON/OFF
Figure 6. Defeating Undervoltage Lockout
HOT-SWAP CONTROLLER
5V LOGIC
GND
LOGIC CONTROL OF 3.3V OR LESS MAY BE CONNECTED
DIRECTLY TO THE MAX5902/MAX5903. FOR 5V LOGIC
CONTROL INSERT A SERIES 47k& RESISTOR AS SHOWN.
47k&
MAX5902
MAX5903
GND
ON/OFF
Figure 5. Logic Control
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5909EEE+ | IC HOT-SWAP CTRLR DUAL 16QSOP |
| MAX5911ESA | IC SW HOTSWAP -48V SWAPPER 8SOIC |
| MAX5913AEMH+ | IC HOT SWAP CTLR QUAD 48V 44MQFP |
| MAX5916EUI+ | IC HOT-SWAP CTRLR DUAL 28-TSSOP |
| MAX5917BESE+ | IC HOT-SWAP SWITCH 65V 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5903LAEUT | 制造商:Maxim Integrated Products 功能描述:SIMPLE SWAPPER HOT-SWAP SWITCHES - Rail/Tube |
| MAX5903LAEUT+ | 制造商:Maxim Integrated Products 功能描述:+72V SOT23/TDFN SIMPLE SWAPPER HOT-SWAP CONTROLLERS - Bulk |
| MAX5903LAEUT+T | 功能描述:熱插拔功率分布 72V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5903LAEUT-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5903LBETT | 制造商:Maxim Integrated Products 功能描述:SIMPLE SWAPPER HOT-SWAP SWITCHES - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。