- 您現在的位置：買賣IC網 > Datasheet目錄43 > MAX5920BESA+ (Maxim Integrated)IC HOT-SWAP CTRLR -48V 8-SOIC Datasheet資料下載
參數資料
| 型號： | MAX5920BESA+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 8/18頁 |
| 文件大小： | 310K |
| 描述： | IC HOT-SWAP CTRLR -48V 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | -20 V ~ -80 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
Detailed Description
The MAX5920A/MAX5920B are integrated hot-swap
controllers for -48V power systems. They allow circuit
boards to be safely hot plugged into a live backplane
without causing a glitch on the power-supply rail. When
circuit boards are inserted into a live backplane, the
bypass capacitors at the input of the boards power
module or switching power supply can draw large
inrush currents as they charge. The inrush currents can
cause glitches on the system power-supply rail and
damage components on the board.
The MAX5920A/MAX5920B provide a controlled turn-on
to circuit cards preventing glitches on the power-supply
rail and damage to board connectors and components.
Both the MAX5920A and MAX5920B provide undervolt-
age, overvoltage, and overcurrent protection. The
MAX5920A/MAX5920B ensure the input voltage is sta-
ble and within tolerance before applying power to the
load. The devices also provide protection against input
voltage steps. During an input voltage step, the
MAX5920A/MAX5920B limit the current drawn by the
load to a safe level without turning off power to the load.
-48V Hot-Swap Controller
with External R
SENSE
8 _______________________________________________________________________________________
Pin Description
PIN
MAX5920A MAX5920B
NAME
FUNCTION
1
PWRGD
Power-Good Signal Output. PWRGD is an active-low open-drain status output referenced
to V
EE
. PWRGD is latched low when V
DRAIN
- V
EE
d V
DL
and V
GATE
> (V
GATE
- V
GH
),
indicating a power-good condition. PWRGD is open drain otherwise.
1
PWRGD
Power-Good Signal Output. PWRGD is an active-high open-drain status output referenced
to DRAIN. PWRGD latches in a high-impedance state when V
DRAIN
- V
EE
d V
DL
and
V
GATE
> (V
GATE
- V
GH
), indicating a power-good condition. PWRGD is pulled low to
DRAIN otherwise.
2
2
OV
Input Pin for Overvoltage Detection. OV is referenced to V
EE
. When OV is pulled above
V
OVH
voltage, the GATE pin is immediately pulled low. The GATE pin remains low until the
OV pin voltage reduces to V
OVL
.
3
3
UV
Input Pin for Undervoltage Detection. UV is referenced to V
EE
. When UV is pulled above
V
UVH
voltage, the GATE is enabled. When UV is pulled below V
UVL
, GATE is pulled low.
UV is also used to reset the circuit breaker after a fault condition. To reset the circuit
breaker, pull UV below V
UVL
. The reset command can be issued immediately after a fault
condition; however, the device does not restart until a t
OFF
delay time has elapsed after
the fault.
4
4
V
EE
Device Negative Power-Supply Input. Connect to the negative power-supply rail.
5
5
SENSE
Current-Sense Voltage Input. Connect to an external sense resistor and the external
MOSFET source. The voltage drop across the external sense resistor is monitored to detect
overcurrent or short-circuit fault conditions. Connect SENSE to V
EE
to disable the current-
limiting feature.
6
6
GATE
Gate Drive Output. Connect to gate of the external N-channel MOSFET.
7
7
DRAIN
Output-Voltage Sense Input. Connect to the output-voltage node (drain of external
N-channel MOSFET). Place the MAX5920_ so the DRAIN pin is close to the DRAIN of the
external MOSFET for the best thermal protection.
8
8
V
DD
Positive Power-Supply Rail Input. This is the power ground in the negative-supply voltage
system. Connect to the higher potential of the power-supply inputs.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX5922AEUI+ | IC NETWORK PWR SW +48V 28-TSSOP |
| MAX5923EUP+T | IC HOT-SWAP SWITCH +60V 20-TSSOP |
| MAX5926EEE+ | IC HOT-SWAP CONTROLLER 16QSOP-EP |
| MAX5929BEEG+ | IC HOT SWAP CTLR QUAD 24QSOP |
| MAX5930AEEG+ | IC HOT SWAP CTLR PWR SEQ 24QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5920BESA+ | 功能描述:熱插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5920BESA+T | 功能描述:熱插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5920BESA-T | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5920CESA | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5920CESA+ | 功能描述:熱插拔功率分布 48V- Hot-Swap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。